1.INSTALL CENTER NO. 1 SUPPORT BEARING ASSEMBLY
| *a | Front Side |
Install the center support bearing to the intermediate shaft.
Coat the splines of the intermediate shaft with MP grease.
Install the washer.
| *1 | Matchmark |
Align the matchmarks on the center yoke and intermediate shaft, and then install the yoke to the shaft.
Install the washer.
Clamp the center yoke in a vise between aluminum plates and press the bearing into position by installing a new nut.
Loosen the nut.
Tighten the nut again.
Using a chisel and hammer, stake the lock nut.
2.INSTALL UNIVERSAL JOINT SPIDER ASSEMBLY
Use the same procedure for all universal joint spiders.
Apply MP grease to a new spider and 2 new spider bearings.
Be careful not to apply too much grease.
Fit the spider into the flange yoke.
Using SST, install the spider bearings to the spider.
Using SST, adjust the spider bearings so that: 1) the yoke does not overlap the snap ring grooves of the spider bearings; 2) the grooves are as wide as possible; and 3) the groove width on both sides is the same.
Install 2 new snap rings to the installed spider bearings. The snap rings must have equal thickness and allow 0 to 0.05 mm (0 to 0.00196 in.) of axial play.
| Part No. | Thickness | Color |
|---|---|---|
| 90080-52044 | 1.384 mm (0.0545 in.) | Green |
| 90080-52174 | 1.39 mm (0.0547 in.) | Green |
| 90080-52043 | 1.435 mm (0.0565 in.) | Purple |
| 90080-52175 | 1.44 mm (0.0567 in.) | Orange |
| 90080-52041 | 1.486 mm (0.0585 in.) | Black |
| 90080-52176 | 1.49 mm (0.0587 in.) | Black |
| 90080-52042 | 1.511 mm (0.0595 in.) | Copper |
| 90080-52040 | 1.537 mm (0.0605 in.) | White |
| 90080-52177 | 1.54 mm (0.0606 in.) | White |
| 90080-52039 | 1.588 mm (0.0625 in.) | Yellow |
| 90080-52178 | 1.59 mm (0.0626 in.) | Yellow |
| 90080-52038 | 1.638 mm (0.0645 in.) | Blue |
| 90080-52179 | 1.64 mm (0.0646 in.) | Red |
| 90080-52180 | 1.69 mm (0.0665 in.) | Blue |
| 90080-52156
* |
1.49 mm (0.0587 in.) | - |
*: For cup with grease nipple.
New snap rings must be used.
The snap ring thickness must be the same on both ends.
| *a | Hammering Point |
Using a plastic-faced hammer, tap the flange yoke until there is no clearance between the spider bearings and snap rings.
Align the matchmarks on the yoke and shaft (or center yoke and sleeve yoke), and install the yoke together with the spider.
Install new spider bearings on the shaft side.
Use the procedure described above.
3.INSTALL REAR SLIDING SHAFT BOOT
Temporarily install a new boot to the propeller shaft with 2 new clamps.
Mount the propeller shaft in a soft vise.
Coat the splines of the propeller shaft with MP grease.
Align the matchmarks on the propeller shaft and sleeve yoke.
Install the sleeve yoke to the propeller shaft and connect the boot.
Secure one of the boot clamps to the boot.
Place SST onto the boot clamp.
Tighten SST so that the boot clamp is pinched as shown in the illustration.
Do not overtighten SST.
Using SST, adjust the clearance of the boot clamp.
0.8 mm (0.0314 in.) or less
Secure the remaining boot clamp to the boot.
Use the procedure described above.
4.INSPECT PROPELLER SHAFT GREASE FITTING DIRECTION
When replacing a spider bearing, be sure that the grease fitting hole is facing the direction shown in the illustration.
Fill the grease fittings with MP grease.
| *1 | No. 1 Grease Fitting | *2 | No. 2 Grease Fitting |
| *3 | No. 3 Grease Fitting | - | - |
| *a | Spider grease fitting assembly direction for propeller shaft assembly | *b | *Rear Side |
5.INSPECT UNIVERSAL JOINT SPIDER ASSEMBLY