Home › Drivetrain › AXLE AND DIFFERENTIAL › STEERING KNUCKLE(for 4WD and Pre-Runner)
RM1840EF _52 Drivetrain _009618 AXLE AND DIFFERENTIAL _0052557 STEERING KNUCKLE(for 4WD and Pre-Runner) A

AXLE AND DIFFERENTIAL  STEERING KNUCKLE(for 4WD and Pre-Runner)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.INSTALL FRONT AXLE HUB ASSEMBLY

F042759

a.

Apply MP grease to a new O-ring.


b.

Install the O-ring to the axle hub.


c.

Install the dust cover and axle hub to the steering knuckle with the 4 bolts.

Torque:
80 N*m (816 kgf*cm, 59 ft.*lbf)


Hide 2.INSTALL FRONT AXLE HUB DUST SEAL (for 4WD)

F042767
1.76,0.771 2.385,0.458 false 2.385,0.458 2.563,0.458 false 2.635,0.365 2.948,0.563 0.313,0.198 10 false SST

a.

Using SST and a press, press in a new dust seal.

SST
09527-17011  
09950-70010  (09951-07100)
09951-01000  


Hide 3.INSTALL KNUCKLE GREASE RETAINER CAP LH (for Pre-Runner)

F042765

a.

Using a brass bar and hammer, install a new retainer cap.

NOTICE:

Do not damage the retainer cap.



Hide 4.CONNECT FRONT UPPER SUSPENSION ARM ASSEMBLY LH

F043605

a.

Connect the upper arm with the nut.

Torque:
110 N*m (1122 kgf*cm, 81 ft.*lbf)


b.

Install a new clip.

NOTICE:

If the holes for the clip are not aligned, tighten the nut an additional 60°.



Hide 5.CONNECT FRONT LOWER SUSPENSION ARM ASSEMBLY LH

F050870

a.

Connect the suspension arm with the 2 bolts.

Torque:
160 N*m (1632 kgf*cm, 118 ft.*lbf)


Hide 6.CONNECT TIE ROD END SUB-ASSEMBLY LH

Hide 7.CONNECT FRONT STABILIZER LINK ASSEMBLY LH

C099158

a.

Connect the stabilizer link with the nut.

Torque:
70 N*m (714 kgf*cm, 52 ft.*lbf)

HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud.



Hide 8.INSTALL FRONT AXLE SHAFT NUT LH (for 4WD)

a.
F042732

Clean the threaded parts on the drive shaft and axle shaft nut using a non-residue solvent.


b.

Install the hub nut.

Torque:
235 N*m (2396 kgf*cm, 173 ft.*lbf)


c.

Install the adjusting cap and a new cotter pin.

NOTICE:

If the holes for the cotter pin are not aligned, tighten the nut an additional 60°.



Hide 9.INSTALL FRONT AXLE HUB GREASE CAP (for 4WD)

a.

Install a new grease cap to the axle hub.


Hide 11.CONNECT FRONT DISC BRAKE CYLINDER ASSEMBLY LH

F050211

a.

Install the disc brake cylinder with the 2 bolts.

Torque:
122 N*m (1244 kgf*cm, 90 ft.*lbf)


b.
F042731

Install the brake tube bracket to the steering knuckle with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 12.INSTALL SPEED SENSOR FRONT LH (w/ ABS)

C113715

a.

Install the speed sensor with the bolt.


b.

Connect the 2 clamps.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


c.

Install the speed sensor wire harness to the steering knuckle with the bolt.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


Hide 13.INSTALL FRONT WHEEL

Torque:
105 N*m (1071 kgf*cm, 77 ft.*lbf)