Home › Drivetrain › AXLE AND DIFFERENTIAL › DIFFERENTIAL OIL › 2011.10–2012.10
RM1840EF _52 Drivetrain _009618 AXLE AND DIFFERENTIAL _0052560 DIFFERENTIAL OIL A

AXLE AND DIFFERENTIAL  DIFFERENTIAL OIL  REPLACEMENT  


PROCEDURE

Hide 1.DRAIN DIFFERENTIAL OIL

a.
A272242
1.646,0.906 2.094,0.813 true 0.24,4.094 0.365,3.708 true 0.24,4.333 0.542,4.438 true 0.979,3.958 1.281,4.063 true 1.49,3.719 1.792,3.823 true 0.573,4.375 0.885,4.531 0.313,0.156 10 false *1 0.344,3.51 0.656,3.667 0.313,0.156 10 false *2 1.823,3.74 2.135,3.896 0.313,0.156 10 false *3 1.313,4 1.771,4.198 0.458,0.198 10 false SST 2.146,0.708 2.604,0.906 0.458,0.198 10 false SST
*1 10 mm Straight Hexagon Wrench
*2 10 mm Union Nut Wrench
*3 Socket Adaptor


for front differential:

i.

Stop the vehicle on a level surface.


ii.

Using SST and the 10 mm straight hexagon wrench, 10 mm union nut wrench and socket adaptor, remove the differential filler plug and gasket.

SST
09961-00950  


iii.

Remove the drain plug and gasket, and drainthe oil.


iv.

Install a new gasket and the drain plug.

Torque:
64.7 N*m (660 kgf*cm, 48 ft.*lbf)



b.

for rear differential:

i.

Stop the vehicle on a level surface.


ii.

Remove the differential filler plug and gasket.


iii.

Remove the drain plug and gasket, and drain the oil.


iv.

Install a new gasket and the drain plug.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)



Hide 2.ADD DIFFERENTIAL OIL

a.
D025304
0.677,1.354 0.854,1.542 0.177,0.188 10 false *a
*a 0 to 5 mm (0 to 0.196 in.)


Add differential oil so that the oil level is within 5 mm (0 to 0.196 in.) from the bottom lip of the differential filler plug hole.

NOTICE:
·

After changing the oil, drive the vehicle, and then check the oil level again.

·

Too much or too little oil will lead to differential problems.



If necessary, fill the differential carrier with hypoid gear oil.

Recommended Viscosity:
Item Temperature Viscosity
Front Differential (w/ A.D.D.) SAE 75W-90
Front Differential (w/o A.D.D.)
Rear Differential
Above -18°C (0°F) SAE 90
Below -18°C (0°F) SAE 80W-90 or SAE 80W


Differential Oil Type:
Item Oil type
Front Differential
Rear Differential
Hypoid gear oil API GL-5 or equivalent
Rear Differential (for LSD) Hypoid gear oil LSD API GL-5 or equivalent


Standard Front Differential Oil Capacity:
Item Capacity
w/o A.D.D. 1.40 to 1.50 liters (1.48 to 1.58 US qts., 1.23 to 1.32 Imp. qts.)
w/ A.D.D. 1.60 to 1.70 liters (1.69 to 1.79 US qts., 1.41 to 1.49 Imp. qts.)


Standard Rear Differential Oil Capacity:
Item Capacity
for LSD
4WD and Pre-runner
for DANA Made
3.30 to 3.40 liters (3.49 to 3.59 US qts., 2.91 to 2.99 Imp. qts.)



b.

Check for oil leakage when the oil level is low.


c.
A272243
1.167,0.833 1.615,0.813 true 0.958,4.021 1.333,4.208 true 1.469,3.813 1.844,3.938 true 0.448,3.844 0.24,4.177 true 0.49,4.531 0.271,4.427 true 0.479,4.448 0.792,4.604 0.313,0.156 10 false *1 0.458,3.719 0.771,3.875 0.313,0.156 10 false *2 1.885,3.896 2.198,4.052 0.313,0.156 10 false *3 0.854,0.771 1.313,0.969 0.458,0.198 10 false SST 1.375,4.188 1.833,4.385 0.458,0.198 10 false SST 2.229,1.927 2.688,2.125 0.458,0.198 10 false L3 2.458,1.021 2.885,1.229 0.427,0.208 10 false L1 2.021,0.958 2.448,1.167 0.427,0.208 10 false L2
*1 10 mm Straight Hexagon Wrench
*2 10 mm Union Nut Wrench
*3 Socket Adaptor


for front differential:

i.

Using SST and the 10 mm straight hexagon wrench, 10 mm union nut wrench and socket adaptor, install a new gasket and the differential filler plug.

SST
09961-00950  

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)

NOTICE:
·

Make sure all the tools are connected in a straight line.


·

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench



Formula:

T' = T x L3 / (L1 + L2 + L3)- T' = Spec. value of torque

- T' = Spec. value of torque wrench

- T = Value of specified tightening torque

- L1 = Length of union nut wrench

- L2 = Length of SST

- L3 = Length of torque wrench




d.

for rear differential:

i.

Install a new gasket and the differential filler plug.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)