Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE SHAFT › from 2012.10
RM1840EF _52 Drivetrain _009618 AXLE AND DIFFERENTIAL _0052567 REAR AXLE SHAFT A

AXLE AND DIFFERENTIAL  REAR AXLE SHAFT  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE BACKING PLATE TO REAR AXLE HOUSING SETTING BOLT

a.
C190684

Temporarily install 4 nuts to the setting bolts.

NOTICE:

Do not use any nuts removed from the vehicle, as they may be damaged.



b.

Using a hammer, tap out the 4 setting bolts from the backing plate.


c.

Remove the 4 nuts and 4 setting bolts.


Hide 2.REMOVE REAR AXLE BEARING INNER RETAINER LH AND REAR SKID CONTROL ROTOR (w/ ABS)

a.
C190685

Grind the retainer and skid control rotor surfaces using a grinder, and then pry off the retainer and skid control rotor with a chisel and hammer.

NOTICE:

Be careful not to damage the axle shaft.



Hide 3.REMOVE REAR AXLE BEARING INNER RETAINER LH (w/o ABS)

a.
C190686

Using a snap ring expander, remove the snap ring.


b.
C190689

Grind the retainer surface using a grinder, and then pry off the retainer with a chisel and hammer.

NOTICE:

Be careful not to damage the axle shaft.



c.

Remove the shaft washer from the axle shaft.


Hide 4.REMOVE REAR AXLE SHAFT LH

a.

Insert the setting bolts into the backing plate and temporarily install washers and nuts to the setting bolts. Tighten the nuts to temporarily install the setting bolts to the backing plate and bearing case.


b.

Remove the nuts and washers from the setting bolts.


c.
C190687
0.552,0.344 1.354,0.344 false 0.208,0.25 0.521,0.396 0.313,0.146 10 false SST

Install SST to the backing plate with the 4 nuts.

SST
09521-25011  


d.
C190688
2.479,0.729 2.292,0.729 2.292,0.729 2.031,1.333 true 2.552,0.635 2.865,0.813 0.313,0.177 10 false SST

Using SST and a press, press out the axle shaft.


e.

Remove the 4 nuts and SST.


f.

Temporarily install 4 nuts to the setting bolts.

NOTICE:

Do not use any nuts removed from the vehicle, as they may be damaged.



g.

Using a hammer, tap out the 4 setting bolts from the backing plate.


h.

Remove the 4 nuts and 4 setting bolts.


Hide 5.REMOVE REAR AXLE HUB BOLT LH

a.
C190690
2.323,0.438 1.896,0.438 false 2.406,0.344 2.698,0.5 0.292,0.156 10 false SST

Secure the axle shaft between aluminum plates in a vise.


b.

for 2WD:

Using SST, remove the 5 hub bolts.

SST
09650-17011  


c.
C191008
2.354,0.521 1.813,0.521 false 2.438,0.427 2.75,0.573 0.313,0.146 10 false SST

for 4WD and Pre-Runner:

Using SST, remove the 6 hub bolts.

SST
09650-17011  


d.

Remove the deflector and gasket from the axle shaft.

NOTICE:
·

Do not deform the deflector.

·

Make sure to align the groove of SST with the flange of the oil deflector.




Hide 6.REMOVE REAR AXLE SHAFT OUTER OIL SEAL

a.
C190691
1.948,1.083 2.5,1.083 false 2.552,1 2.885,1.146 0.333,0.146 10 false SST

Using SST, tap out the outer oil seal.

SST
09308-00010  


Hide 7.REMOVE REAR AXLE SHAFT BEARING LH

a.
C190692
2.479,0.385 2.281,0.385 2.281,0.385 1.938,0.646 false 2.583,0.938 2.406,0.938 2.406,0.938 2.042,1.24 true 2.573,0.292 2.885,0.438 0.313,0.146 10 false SST 2.667,0.844 2.979,0.99 0.313,0.146 10 false SST

Using SST and a press, press out the bearing.

SST
09223-56010  
09950-60010  (09951-00640)