Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY(for DANA Made)
RM1840EF _52 Drivetrain _009618 AXLE AND DIFFERENTIAL _0052568 REAR DIFFERENTIAL CARRIER ASSEMBLY(for DANA Made) A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER ASSEMBLY(for DANA Made)  DISASSEMBLY  


PROCEDURE

Hide 1.FIX REAR DIFFERENTIAL CARRIER ASSEMBLY

C121133

Hide 2.INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY REAR

a.
F001237
1.313,1.927 2.375,2.115 1.063,0.188 10 true 30 mm (1.18 in.)

Using a dial indicator, measure the runout of the companion flange vertically and laterally.

Maximum runout:
Runout Maximum
Vertical runout 0.10 mm (0.0039 in.)
Lateral runout 0.10 mm (0.0039 in.)


If the runout is greater than the maximum, replace the companion flange.



Hide 3.INSPECT RUNOUT OF DIFFERENTIAL RING GEAR

a.
C121134

Using a dial indicator, measure the runout of the ring gear.

Maximum runout:

0.07 mm (0.0028 in.)


If the runout is greater than the maximum, replace the ring gear with a new one.



Hide 4.INSPECT DIFFERENTIAL RING GEAR BACKLASH

a.
C121135

Using a dial indicator, measure the backlash of the ring gear.

Standard backlash:

0.13 to 0.18 mm (0.0051 to 0.0071 in.)


If the backlash is not within the specification, adjust the side bearing preload or repair as necessary.

HINT:

Perform the measurements at 3 or more positions around the side bearing preload.




Hide 5.INSPECT DIFFERENTIAL DRIVE PINION PRELOAD

a.
C003092

Using a torque wrench, measure the preload of backlash between the drive pinion and ring gear.

Standard drive pinion preload (at start of torque):

0.56 to 0.85 N*m (6 to 9 kgf*cm, 4.9 to 7.5 in.*lbf)


If necessary, disassemble and inspect the differential.



Hide 6.INSPECT TOTAL PRELOAD

a.
C003092

Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.


b.

Using a torque wrench, measure the total preload.

HINT:

A bolt without a torque specification is shown in the service data (See page General>SPECIFICATIONS>AXLE AND DIFFERENTIAL>SERVICE DATA).


If necessary, disassemble and inspect the differential.



Hide 7.REMOVE REAR DRIVE PINION NUT

a.
C282514
1.74,1.104 2.25,1.104 false 2.313,0.979 2.698,1.177 0.385,0.198 10 false SST

Using SST and a hammer, loosen the staked part of the nut.

SST
09930-00010  (09931-00010, 09931-00020)


b.
SA02349
2.875,0.49 2.271,0.49 false 2.927,0.406 3.271,0.594 0.344,0.188 10 false SST

Using SST to hold the companion flange in place, remove the nut.

SST
09330-00021  (09330-00030)


Hide 8.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

a.
B087869
1.969,0.594 2.25,0.396 false 2.25,0.396 2.344,0.396 false 2.385,0.302 2.677,0.458 0.292,0.156 10 false SST

Using SST, remove the companion flange.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



Hide 9.REMOVE REAR DIFFERENTIAL DUST DEFLECTOR

a.
C283418
1.719,0.823 2.188,0.417 2.188,0.417 1.76,1.021 false 2.177,0.438 2,0.99 false 2.25,0.323 2.708,0.521 0.458,0.198 10 false SST

Using SST and a press, press out the dust deflector.

SST
09950-60010  (09951-00380)
09950-70010  (09951-07150)
09950-00020  

NOTICE:

Do not drop the companion flange.



Hide 10.REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL

a.
C283419
1.375,0.844 1.208,0.479 1.208,0.479 0.865,0.479 false 0.49,0.375 0.948,0.573 0.458,0.198 10 false SST

Using SST, remove the oil seal from the differential carrier.

SST
09308-10010  


Hide 11.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 12.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
Z000641
1.667,0.771 1.302,0.542 false 1.302,0.542 0.969,0.542 false 0.594,0.448 0.906,0.604 0.313,0.156 10 false SST

Using SST, remove the roller bearing (inner) from the drive pinion.

SST
09556-22010  


Hide 13.REMOVE DIFFERENTIAL CASE ASSEMBLY

a.
C282485
1.583,1.667 0.906,1.875 0.906,1.875 1.625,1.51 false 0.667,1.792 0.979,1.99 0.313,0.198 10 false *a
*a Matchmark


Place matchmarks on the bearing cap and differential carrier.


b.

Remove the 4 bolts and 2 differential bearing caps.


c.

Remove the 2 side shims.


d.
C028220

Remove the rear differential case assembly from the differential carrier.

HINT:

Tag the 2 case bearing outer races to show the location for reassembly.



Hide 14.REMOVE DIFFERENTIAL DRIVE PINION

a.

Remove the drive pinion and bearing spacer from the differential carrier.


Hide 15.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C283420
2.302,1.083 2.531,0.604 2.531,0.604 2.75,0.604 false 2.813,0.479 3.271,0.677 0.458,0.198 10 false SST

Using SST and a press, press out the roller bearing (inner) from the drive pinion.

SST
09950-00020  

NOTICE:

Do not drop the drive pinion.


HINT:

If the drive pinion or ring gear is damaged, replace them as a set.



Hide 16.REMOVE REAR DIFFERENTIAL DRIVE PINION PLATE WASHER

Hide 17.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C282515
1.031,0.24 1.469,0.24 false 1.542,0.167 2,0.365 0.458,0.198 10 false SST

Using SST, remove the roller bearing (outer) from the carrier.

SST
09308-00010  


b.

Using a brass bar and hammer, tap out the oil storage ring from the carrier.

HINT:

If the bearing is damaged during removal, replace it.



Hide 18.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C091047

Using a brass bar and hammer, tap out the rear tapered roller bearing (outer) from the carrier.

HINT:

If the bearing is damaged during removal, replace it.



Hide 19.REMOVE DIFFERENTIAL RING GEAR

a.
C282486
1.823,1.208 1.135,1.677 1.135,1.677 1.771,0.99 false 0.906,1.667 1.125,1.885 0.219,0.219 10 false *a
*a Matchmark


Place matchmarks on the ring gear and differential case.


b.

Remove the 10 ring gear set bolts.


c.
C014054

Using a plastic-faced hammer, tap on the ring gear to separate it from the differential case.


Hide 20.INSPECT DIFFERENTIAL CASE ASSEMBLY RUNOUT

a.

Install the rear differential case bearing to the differential case.


b.

Install the differential case to the differential carrier.


c.

Install the 2 bearing caps to the differential carrier with the 4 bolts.

Torque:
85 N*m (867 kgf*cm, 63 ft.*lbf)


d.
C121138

Using a dial indicator, measure the differential case runout.

Maximum runout:

0.07 mm (0.0028 in.)



e.

Remove the differential case.


f.

Remove the rear differential case bearing.


Hide 21.REMOVE REAR DIFFERENTIAL CASE BEARING

a.
F040345
0.427,0.25 0.844,0.25 false 0.844,0.25 0.844,0.781 false 0.083,0.156 0.396,0.323 0.313,0.167 10 false SST

Using SST, remove the 2 bearings from the differential case.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
09950-60010  (09951-00360)

HINT:

Do not remove the case bearing when not replacing the differential case.



Hide 22.INSPECT DIFFERENTIAL PINION AND SIDE GEAR

a.

Check that the differential pinion and differential side gear are not worn.

If the differential pinion or differential side gear is not worn, replace the differential.



Hide 23.INSPECT DIFFERENTIAL CASE

a.
F014547

Measure the side gear backlash.

i.

Using a dial indicator, measure the side gear backlash while holding one pinion gear toward the differential case.

Standard backlash:

0.05 to 0.20 mm (0.0020 to 0.008 in.)


If the backlash is not within the specified range, replace the differential case with a new one.