Home › Drivetrain › AXLE AND DIFFERENTIAL › DIFFERENTIAL SYSTEM(w/ Differential Lock) › from 2012.10
RM1840EF _52 Drivetrain _009618 AXLE AND DIFFERENTIAL _0052571 DIFFERENTIAL SYSTEM(w/ Differential Lock) G

AXLE AND DIFFERENTIAL  DIFFERENTIAL SYSTEM(w/ Differential Lock)  INSPECTION  


PROCEDURE

Hide 1.INSPECT DIFFERENTIAL LOCK SYSTEM

a.
C238713

Inspect the indicator light.

i.

Check that the indicator light lights up for approximately 1 second when the ignition switch is turned to ON.



b.

Inspect the differential lock operation.

i.

Jack up the vehicle and start the engine.


ii.

Shift the transfer shift lever to the L position.


iii.

When the differential lock control switch is set to the ON position, the indicator light turns on. Differential lock is applied to the rear wheel at this time.

HINT:

If the gears of the differential lock system are not meshed, the indicator light remains blinking, so rotate the tires to mesh the gears.



iv.

When the differential lock control switch is at the OFF position, the indicator light goes off. Differential lock is released for the rear wheel at this time.


v.
C123204
2.021,0.906 2.021,0.417 2.021,0.417 2.323,0.417 true 1.104,0.427 1.406,0.427 1.406,0.427 1.406,0.896 true 0.823,0.323 1.052,0.469 0.229,0.146 10 false M1 2.438,0.333 2.667,0.479 0.229,0.146 10 false M2 0.115,0.104 0.281,0.26 0.167,0.156 10 false *a
*a ECU Side


Check the voltage between the terminals of the four wheel drive control ECU when switching the differential control switch with the speedometer registering approximately 8 km/h (5 mph) or more.

Switch Position Terminal Specified Condition
ON 3 (M1) to 2 (M2) 0.5 V or less (No change)


vi.

Return the differential lock control switch to OFF.


vii.

Stop the engine and lower the vehicle.



Hide 2.CHECK WIRE HARNESS AND CONNECTOR

a.
C123205
2.25,0.896 2.25,0.573 2.25,0.573 2.542,0.573 true 2.188,0.219 2.031,0.219 2.031,0.219 2.031,0.885 true 1.385,0.885 1.385,0.229 1.385,0.229 1.542,0.229 true 1.167,0.896 1.167,0.552 1.167,0.552 0.854,0.552 true 1.135,1.292 1.135,1.583 1.135,1.583 0.635,1.583 true 1.604,1.313 1.604,1.875 1.604,1.875 1.448,1.875 true 1.823,1.292 1.823,1.896 1.823,1.896 2.063,1.896 true 2.24,1.281 2.24,1.729 2.24,1.729 2.677,1.729 true 2.26,0.135 2.49,0.281 0.229,0.146 10 false M1 1.615,0.135 1.844,0.281 0.229,0.146 10 false M2 2.656,0.469 2.781,0.635 0.125,0.167 10 false R 0.396,1.51 0.573,1.667 0.177,0.156 10 false IG 1.083,1.802 1.51,1.969 0.427,0.167 10 false GND 2.083,1.813 2.5,1.99 0.417,0.177 10 false 4WD 2.771,1.635 3.104,1.781 0.333,0.146 10 false SPD 0.531,0.469 0.823,0.615 0.292,0.146 10 false RLP 0.094,0.083 0.281,0.25 0.188,0.167 10 false *a
*a Wire Harness Side


Inspect the system circuit with the connector disconnected.

i.

Disconnect the connector from the four wheel drive control ECU and inspect the connector on the wire harness side as shown in the table.

Standard Voltage
Tester Connection Trouble Part Condition Specified Condition
3 (M1) - 2 (M2) Rear differential lock actuator - Less than 100 Ω
7 (GND) - Body ground Body ground - Below 1 Ω
10 (SPD) - Body ground Speed sensor Vehicle moves slowly 1 pulse generation per 40 cm (15.75 in.)
5 (IG) - Body ground Differential fuse Ignition switch ON 10 to 14 V
1 (RLP) - Body ground Rear differential lock indicator switch Ignition switch ON with indicator light ON About 0 V
Ignition switch ON with indicator light OFF 10 to 14 V
8 (4WD) - Body ground L position switch Ignition switch ON with transfer shift lever not in L About 0 V
Ignition switch ON with transfer shift lever in L 10 to 14 V
4 (R) - Body ground Differential lock control switch Ignition switch ON with differential lock control switch ON 10 to 14 V
Ignition switch ON with differential lock control switch OFF About 0 V

HINT:

If the result is not as specified, check and repair or replace the trouble part shown in the table above.




Hide 3.CHECK FOUR WHEEL DRIVE CONTROL ECU NO. 2

a.
C123206
1.615,1.292 1.063,1.844 1.063,1.844 0.813,1.844 true 1.813,1.271 2.021,1.833 2.021,1.833 2.604,1.833 true 2.021,0.896 2.021,0.125 2.021,0.125 2.24,0.125 true 1.406,0.906 1.406,0.531 1.406,0.531 0.906,0.531 true 2.26,0.906 2.26,0.375 2.26,0.375 2.573,0.375 true 0.635,0.438 0.948,0.604 0.313,0.167 10 false M1 2.323,0.031 2.542,0.188 0.219,0.156 10 false M2 2.646,0.302 3.021,0.479 0.375,0.177 10 false RLP 0.427,1.771 0.76,1.927 0.333,0.156 10 false 4WD 2.677,1.74 3.104,1.906 0.427,0.167 10 false GND 0.094,0.052 0.271,0.208 0.177,0.156 10 false *a
*a ECU Side


Inspect the system circuit with the connector connected.

i.

Turn the ignition switch to ON.


ii.

Shift the transfer shift lever to the L position.


iii.

Using a voltmeter, measure the voltage when the differential lock control switch is in the position shown in the table.

Standard Voltage
Tester Connection Switch Position Specified Condition
8 (4WD) - 7 (GND) - 0.5 V or less
1 (RLP) - 7 (GND) ON* 0.5 V or less
3 (M1) - 2 (M2) OFF → ON 0.5 V or less → 10 to 14 V (approx. 1 sec.) → 0.5 V or less
2 (M2) - 3 (M1) ON → OFF

HINT:

*: The rear differential should be locked mechanically.

If the result is not as specified, replace the ECU.




iv.

Install the ECU.



Hide 4.INSPECT DIFFERENTIAL LOCK COMPONENTS

a.

Inspect the relay operation.

i.

Jack up the vehicle.


ii.

Use a heater main relay and connect it as shown below.

NOTICE:

Connect the terminals while being careful not to touch the neighboring terminals or metallic parts of the relay housing.



iii.

Rotate the tire and check that the differential lock has occurred.

C123208
2.677,3.5 2.677,3.313 false 2.969,3.719 3.188,3.656 false 2.688,3.854 3.104,4.313 false 2.656,4.083 2.656,4.271 false 2.323,3.813 2.323,4.302 false 0.948,3.969 1.146,4.208 0.198,0.24 10 false 1 1.792,3.99 1.948,4.24 0.156,0.25 10 false 2 1.792,3.583 1.958,3.823 0.167,0.24 10 false 3 1.375,3.073 1.563,3.323 0.188,0.25 10 false 4 0.948,3.594 1.167,3.833 0.219,0.24 10 false 5 2.635,3.146 2.833,3.365 0.198,0.219 10 false 1 2.615,4.281 2.76,4.479 0.146,0.198 10 false 2 2.281,4.323 2.458,4.573 0.177,0.25 10 false 3 3.104,4.292 3.26,4.5 0.156,0.208 10 false 4 3.208,3.583 3.354,3.802 0.146,0.219 10 false 5 1.271,1.385 1.427,1.583 0.156,0.198 10 false 1 2.083,1.406 2.229,1.583 0.146,0.177 10 false 2 2.073,1.01 2.25,1.219 0.177,0.208 10 false 3 1.75,0.604 1.927,0.802 0.177,0.198 10 false 4 1.271,0.979 1.458,1.198 0.188,0.219 10 false 5 4.885,1.385 5.052,1.604 0.167,0.219 10 false 1 5.698,1.396 5.844,1.552 0.146,0.156 10 false 2 5.688,1 5.813,1.188 0.125,0.188 10 false 3 5.365,0.594 5.552,0.865 0.188,0.271 10 false 4 4.885,0.979 5.042,1.146 0.156,0.167 10 false 5 0.833,0.177 1.094,0.427 0.26,0.25 10 false *a 0.677,3.031 0.865,3.198 0.188,0.167 10 false *1 4.271,0.188 4.51,0.385 0.24,0.198 10 false *b
*1 Heater Main Relay - -
*a Free → Lock *b Lock → Free


If the operation is not as specified, replace the actuator.




Hide 5.INSPECT DIFFERENTIAL LOCK SWITCH

a.
C237511
0.153,0.077 0.328,0.256 0.175,0.179 10 *a
*a Component without harness connected
(Differential Lock Switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 - 4 OFF 10 kΩ or higher
ON Below 1 Ω


If the result is not as specified, replace the switch.


Hide 6.INSPECT NO. 4 TRANSFER INDICATOR SWITCH

a.
C237700
0.204,0.157 0.381,0.327 0.177,0.17 10 *a
*a Component without harness connected
(No. 4 Transfer Indicator Switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 - 1 Pushed Below 1 Ω
Not pushed 100 kΩ or higher


If the result is not as specified, replace the No. 4 transfer indicator switch.