Home › Suspension › FRONT SUSPENSION › FRONT LOWER SUSPENSION ARM(for 4WD and Pre-Runner)
RM1840EF _53 Suspension _009620 FRONT SUSPENSION _0052579 FRONT LOWER SUSPENSION ARM(for 4WD and Pre-Runner) A

FRONT SUSPENSION  FRONT LOWER SUSPENSION ARM(for 4WD and Pre-Runner)  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 2.DISCONNECT FRONT SHOCK ABSORBER WITH COIL SPRING

F049985

a.

Remove the nut and bolt.

HINT:

While fixing the nut in place, loosen and remove the bolt.



b.

Disconnect the shock absorber with coil spring from the lower arm.


Hide 3.REMOVE FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY LH

F050007

a.

Remove the 2 bolts, and disconnect the ball joint attachment from the steering knuckle.


b.
F050008C02
0.833,0.896 1.802,0.281 1.802,0.281 2.583,0.75 true 1.74,0.104 2.052,0.26 0.313,0.156 10 false *1
*1 Matchmark


Place matchmarks on the No. 1 camber adjusting cam and vehicle frame, and No. 2 camber adjusting cam and vehicle frame.


c.

Remove the 2 nuts, No. 1 and No. 2 camber adjusting cams, 2 camber adjusting cams and lower arm.


Hide 4.REMOVE FRONT LOWER BALL JOINT ATTACHMENT

a.

Remove the cotter pin and nut.


b.
F051058
2.969,0.74 2.646,0.74 false 2.99,0.625 3.344,0.833 0.354,0.208 10 false SST

Using SST, remove the ball joint attachment.

SST
09628-00011  


Hide 5.REMOVE FRONT NO. 1 LOWER ARM BUSH

a.
F050010

Using a hammer and chisel, strike and bend the entire flange of the bush as shown in the illustration.


b.
F050011
1.521,1.823 1.385,1.823 false 1.24,1.552 1.385,1.823 true 1.156,0.469 1.5,0.26 false 1.5,0.26 1.135,0.74 false 1.531,1.708 1.833,1.906 0.302,0.198 10 false SST 1.531,0.146 1.833,0.344 0.302,0.198 10 false SST

Using SST and a press, press out the bush.

SST
09632-36010  
09950-00020  
09950-60010  (09951-00520)


Hide 6.REMOVE FRONT NO. 2 LOWER ARM BUSH

a.
F050010

Using a hammer and chisel, strike and bend the entire flange of the bush as shown in the illustration.


b.
F050012
1.552,1.833 1.385,1.833 false 1.385,1.833 1.219,1.563 true 0.469,0.458 0.854,0.573 false 0.469,0.458 0.875,0.792 false 1.563,1.708 1.865,1.906 0.302,0.198 10 false SST 0.135,0.354 0.438,0.552 0.302,0.198 10 false SST

Using SST and a press, press out the bush.

SST
09632-36010  
09950-00020  
09950-60010  (09951-00400)


Hide 7.REMOVE LOWER BALL JOINT ASSEMBLY

a.
C237854
0.708,1.115 1.531,1.115 true 0.49,1 0.771,1.188 0.281,0.188 10 false *a
*a Protective tape


Using 2 screwdrivers and a hammer, remove the snap ring.

HINT:

Tape the screwdriver tip before use.



b.

Remove the dust cover set ring and dust cover from the lower arm.


c.
C280975
2.302,2.208 2.094,2.208 2.094,2.208 1.906,1.427 true 0.969,0.99 1.552,0.99 false 0.49,0.052 0.802,0.25 0.313,0.198 10 false *a 3.115,0.177 3.427,0.375 0.313,0.198 10 false *b 2.354,2.146 2.813,2.344 0.458,0.198 10 false SST 0.656,0.917 1.115,1.115 0.458,0.198 10 false SST
*a Hold
*b Turn


Using SST, remove the ball joint.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04031, 09957-04010, 09958-04011)
09710-22021  (09710-01081)


Hide 8.REMOVE FRONT SPRING BUMPER

a.

Remove the front spring bumper from the vehicle.