Home › Suspension › FRONT SUSPENSION › FRONT UPPER SUSPENSION ARM(for 2WD) › from 2012.10
RM1840EF _53 Suspension _009620 FRONT SUSPENSION _0052583 FRONT UPPER SUSPENSION ARM(for 2WD) A

FRONT SUSPENSION  FRONT UPPER SUSPENSION ARM(for 2WD)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.INSTALL FRONT UPPER BALL JOINT

a.
C237853N02
0.844,0.938 1.677,0.448 true 1.677,0.448 1.99,0.448 false 0.51,1.875 0.677,2.302 false 0.667,2.292 0.896,2.292 false 2.083,0.344 2.479,0.563 0.396,0.219 10 false SST 1.01,2.177 1.406,2.396 0.396,0.219 10 false SST

Using SST and a press, press in a new upper ball joint.

SST
09612-30012  
09223-00010  


b.

Using a snap ring expander, install a new snap ring.

NOTICE:

Make sure the snap ring is securely installed in the groove.



Hide 2.INSTALL UPPER BALL JOINT DUST COVER

a.
C159213C03
2.063,0.948 2.5,0.948 2.5,0.948 2.5,1.719 true 1.906,1.25 2,1.25 false 1.427,1.25 1.521,1.25 false 2.5,1.458 2.208,1.458 false 2.208,1.458 1.969,1.26 false 1.427,1.25 0.979,1.25 false 0.75,1.167 0.958,1.313 0.208,0.146 10 false *1 2.375,1.75 2.583,1.896 0.208,0.146 10 false *1
*1 MP Grease No. 2


Pack the upper ball joint with MP grease No. 2.

Grease capacity:

8.0 g (0.282 oz.)



b.

Apply MP grease No. 2 to the locations shown in the illustration.

NOTICE:

Do not apply MP grease No. 2 to the tapered or threaded parts of the ball joint.



c.

Install a new dust cover to the upper arm.


d.

Install a new dust cover set ring.


Hide 3.INSTALL FRONT UPPER SUSPENSION ARM BUSH

a.
F049921N02
0.396,0.385 0.677,0.385 false 0.677,0.385 0.865,0.51 false 0.052,0.271 0.365,0.469 0.313,0.198 10 false SST

Using SST and a press, press in a new upper arm bush.

SST
09710-22021  (09710-01031)


Hide 4.TEMPORARILY INSTALL FRONT UPPER SUSPENSION ARM ASSEMBLY LH

F049917

a.

Temporarily install the upper arm with the 2 bolts and 2 nuts.

HINT:

Fix the nuts in place and temporarily install the bolts.



b.

Install the upper arm to the front axle with the nut.

Torque:
110 N*m (1122 kgf*cm, 81 ft.*lbf)


c.

Install a new clip.


Hide 5.CONNECT FRONT FLEXIBLE HOSE

a.

Connect the front flexible hose with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 6.INSTALL FRONT WHEEL

Torque:
152 N*m (1550 kgf*cm, 112 ft.*lbf)

Hide 8.TIGHTEN FRONT UPPER SUSPENSION ARM ASSEMBLY LH

a.

Tighten the 2 bolts of the upper arm.

Torque:
85 N*m (867 kgf*cm, 63 ft.*lbf)


Hide 9.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT