Home › Suspension › FRONT SUSPENSION › FRONT LOWER SUSPENSION ARM(for 2WD) › from 2012.10
RM1840EF _53 Suspension _009620 FRONT SUSPENSION _0052584 FRONT LOWER SUSPENSION ARM(for 2WD) A

FRONT SUSPENSION  FRONT LOWER SUSPENSION ARM(for 2WD)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.INSTALL LOWER BALL JOINT ASSEMBLY

a.
C237856N02
1.594,0.177 2.115,0.177 2.115,0.177 2.625,0.844 true 2.448,2.323 2.75,2.323 false 2.75,2.323 2.906,1.938 false 1.208,0.115 1.615,0.323 0.406,0.208 10 false SST 2.031,2.24 2.438,2.448 0.406,0.208 10 false SST

Using SST and press, press in a new lower ball joint.

SST
09226-10010  
09631-32020  


b.

Install a new snap ring.

NOTICE:

Make sure the snap ring is securely installed in the groove.



c.
C237891C01
1.615,0.75 1.76,0.75 false 2.115,0.75 2.25,0.75 false 1.646,0.771 1.76,0.771 false 2.115,0.771 2.229,0.771 false 0.844,0.583 1.677,0.583 false 1.677,0.583 1.677,0.74 false 1.156,0.594 1.156,1.115 1.156,1.115 1.583,1.115 true 0.656,0.5 0.885,0.688 0.229,0.188 10 false *1
*1 MP Grease No. 2


Pack the upper ball joint with MP grease No. 2.

Grease capacity:

8.0 g (0.282 oz.)



d.

Apply MP grease No. 2 to the locations shown in the illustration.

NOTICE:

Do not apply MP grease No. 2 to the tapered or threaded parts of the ball joint.



e.

Install a new dust cover to the lower arm.


f.

Install a new dust cover set ring.


Hide 2.INSTALL FRONT NO. 2 LOWER ARM BUSH

a.
C281875C01
0.625,0.708 0.438,0.708 false 0.677,1.521 0.49,1.354 false 0.458,3.417 0.938,3.021 0.938,3.021 0.458,3.938 true 1.01,2.927 1.323,3.083 0.313,0.156 10 false *a 0.104,0.625 0.563,0.823 0.458,0.198 10 false SST 0.156,1.25 0.615,1.448 0.458,0.198 10 false SST
*a Bush Positioning Protrusion


Using SST and a press, install a new bush.

SST
09710-20011  (09710-03081)
09726-27012  (09726-02041)

NOTICE:

Press the bush while making sure the bush positioning protrusions are perpendicular to the lower arm as shown in the illustration.



Hide 3.INSTALL FRONT NO. 1 LOWER ARM BUSH

a.
C281876N01
0.833,1.208 0.563,1.135 0.563,1.135 0.854,1.469 false 0.24,1.052 0.698,1.25 0.458,0.198 10 false SST

Using SST and a press, press in a new bush.

SST
09710-20011  (09710-06071)
09710-22021  (09710-01071)


Hide 4.INSTALL FRONT LOWER BALL JOINT ATTACHMENT LH

a.

Install the ball joint attachment with the nut and a new cotter pin.

Torque:
140 N*m (1428 kgf*cm, 103 ft.*lbf)


Hide 5.TEMPORARILY INSTALL FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY LH

F102351C01
1,0.646 1.698,0.385 1.698,0.385 2.625,0.802 true 1.635,0.219 1.948,0.417 0.313,0.198 10 false *1
*1 Matchmark


a.

Temporarily install the lower arm, and No. 1 and No. 2 camber adjusting cams with the 2 camber adjusting cams and 2 nuts.


b.

Align the matchmarks on the No. 1 camber adjusting cam and No. 2 camber adjusting cam with the corresponding matchmarks on the vehicle frame.


c.
F049924

Install the ball joint attachment with the 2 bolts.

Torque:
160 N*m (1632 kgf*cm, 118 ft.*lbf)


Hide 6.INSTALL FRONT SPRING BUMPER

a.
C237887N02
2.646,1.635 2.365,1.635 false 2.365,1.635 2.146,1.344 true 2.667,1.552 3.021,1.781 0.354,0.229 10 false SST

Using SST, install the front spring bumper to the lower arm.

SST
09922-10010  

Torque:
for use without SST : 31 N*m (316 kgf*cm, 23 ft.*lbf)
for use with SST : 23 N*m (231 kgf*cm, 17 ft.*lbf)

HINT:
·

Rotate SST in the direction shown in the illustration.

·

Use a torque wrench with a fulcrum length of 345 mm (13.6 in.).




Hide 7.TEMPORARILY INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING

a.

Temporarily install the shock absorber with coil spring with the bolt and nut.


Hide 8.CONNECT FRONT STABILIZER LINK ASSEMBLY LH

a.

Connect the stabilizer link to the lower arm with the nut.

Torque:
78 N*m (795 kgf*cm, 58 ft.*lbf)

HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud in place.



Hide 10.INSTALL FRONT WHEEL

Torque:
152 N*m (1550 kgf*cm, 112 ft.*lbf)

Hide 12.TIGHTEN FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY LH

a.

Tighten the 2 nuts.

Torque:
210 N*m (2141 kgf*cm, 155 ft.*lbf)


Hide 13.TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING

a.

Fix the nut in place and tighten the bolt.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)

NOTICE:

Do not tighten the nut.



Hide 14.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT