Home › Suspension › FRONT SUSPENSION › FRONT LOWER SUSPENSION ARM(for 2WD) › from 2012.10
RM1840EF _53 Suspension _009620 FRONT SUSPENSION _0052584 FRONT LOWER SUSPENSION ARM(for 2WD) A

FRONT SUSPENSION  FRONT LOWER SUSPENSION ARM(for 2WD)  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 3.DISCONNECT FRONT SHOCK ABSORBER WITH COIL SPRING

F049906

a.

Remove the nut and bolt.

HINT:

While fixing the nut in place, loosen and remove the bolt.



b.

Disconnect the shock absorber with coil spring from the lower arm.


Hide 4.DISCONNECT FRONT STABILIZER LINK ASSEMBLY LH

a.
C113157

Remove the nut and disconnect the stabilizer link from the lower arm.

HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud in place.



Hide 5.REMOVE FRONT SPRING BUMPER

a.
C280974
0.844,1.875 1.219,1.875 1.219,1.875 1.573,1.406 false 2.792,1.427 3.104,1.625 0.313,0.198 10 *a 0.521,1.802 0.979,2 0.458,0.198 10 SST
*1 Turn


Using SST, remove the front spring bumper.

SST
09922-10010  

NOTICE:

Rotate SST in the direction shown in the illustration.



Hide 6.REMOVE FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY LH

F049924

a.

Remove the 2 bolts, and disconnect the ball joint attachment from the steering knuckle.


b.
F049925
0.99,0.625 1.833,0.313 1.833,0.313 2.625,0.781 true 1.76,0.146 2.073,0.302 0.313,0.156 10 true *1
*1 Matchmark


Place matchmarks on the No. 1 camber adjusting cam and vehicle frame, and No. 2 camber adjusting cam and vehicle frame.


c.

Remove the 2 nuts, No. 1 and No. 2 camber adjusting cams, 2 camber adjusting cams and lower arm.


Hide 7.REMOVE FRONT LOWER BALL JOINT ATTACHMENT LH

a.
F049926
2.958,0.771 2.656,0.771 false 2.979,0.667 3.281,0.865 0.302,0.198 10 false SST

Remove the cotter pin and nut.


b.

Using SST, remove the ball joint attachment.

SST
09628-00011  


Hide 8.REMOVE FRONT NO. 1 LOWER ARM BUSH

a.
F049927

Using a hammer and chisel, strike and bend the entire flange of the bush as shown in the illustration.


b.
F049928
1.448,1.833 1.354,1.833 false 1.354,1.833 1.219,1.594 true 1.156,0.396 1.51,0.313 false 1.51,0.313 1.135,0.625 false 1.469,1.729 1.781,1.927 0.313,0.198 10 false SST 1.542,0.208 1.854,0.406 0.313,0.198 10 false SST

Using SST, and a press, press out the bush.

SST
09632-36010  
09950-00020  
09950-60010  (09951-00520)


Hide 9.REMOVE FRONT NO. 2 LOWER ARM BUSH

a.
F049927

Using a hammer and chisel, strike and bend the entire flange of the bush as shown in the illustration.


b.
F049928
1.448,1.833 1.354,1.833 false 1.354,1.833 1.219,1.594 true 1.156,0.396 1.51,0.313 false 1.51,0.313 1.135,0.625 false 1.469,1.729 1.781,1.927 0.313,0.198 10 false SST 1.542,0.208 1.854,0.406 0.313,0.198 10 false SST

Using SST and a press, press out the bush.

SST
09632-36010  
09950-00020  
09950-60010  (09951-00520)


Hide 10.REMOVE LOWER BALL JOINT ASSEMBLY

a.
C237854
0.708,1.115 1.531,1.115 true 0.49,1 0.771,1.188 0.281,0.188 10 false *a
*a Protective tape


Using 2 screwdrivers and a hammer, remove the snap ring.

HINT:

Tape the screwdriver tip before use.



b.

Remove the dust cover set ring and dust cover from the lower arm.


c.
C280975
2.302,2.208 2.094,2.208 2.094,2.208 1.906,1.427 true 0.969,0.99 1.552,0.99 false 0.49,0.052 0.802,0.25 0.313,0.198 10 false *a 3.115,0.177 3.427,0.375 0.313,0.198 10 false *b 2.354,2.146 2.813,2.344 0.458,0.198 10 false SST 0.656,0.917 1.115,1.115 0.458,0.198 10 false SST
*a Hold
*b Turn


Using SST, remove the ball joint.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04031, 09957-04010, 09958-04011)
09710-22021  (09710-01081)