Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2011.10–2013.10
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052601 VEHICLE STABILITY CONTROL SYSTEM U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TERMINALS OF ECU  


TERMINALS OF ECU


C238997
0.249,0.0070 0.563,0.228 0.314,0.221 10 *a
*a Component without harness connected
(Skid Control ECU [Brake Actuator Assembly])


Terminal No. (Symbol) Terminal Description
1 (GND1) Skid control ECU ground
2 (STP) Stop light switch input
3 (IND) Slip indicator light output
4 (RL-) Rear wheel speed LH (-) signal input
5 (RL+) Rear wheel speed LH (+) power supply output
6 (FR-) Front wheel speed RH (-) signal input
7 (FR+) Front wheel speed RH (+) power supply output
8 (BRL) Brake warning light output
9 (EXI4)*1 L4 position switch input
10 (WA) ABS warning light output
12 (+BS) Solenoid relay power supply
13 (GND2) Pump motor ground
14 (CANL) CAN communication low line
15 (VSCW) VSC OFF indicator light output
16 (RR-) Rear wheel speed RH (-) signal input
17 (RR+) Rear wheel speed RH (+) power supply output
18 (FL-) Front wheel speed LH (-) signal input
19 (FL+) Front wheel speed LH (+) power supply output
20 (EXI)*1 4WD detection switch input
24 (+BM) Motor relay power supply
25 (CANH) CAN communication high line
27 (FSW+) Brake pedal load sensing switch input
28 (EXI3) IG power supply
29 (PKB) Parking brake switch input
30 (CSW) VSC OFF switch input
32 (P)*2 Park/neutral position switch signal input
33 (TS) Sensor check input
34 (IG1) ECU power supply

*1: for 4WD

*2: for Automatic Transmission



TERMINAL INSPECTION


a.
C238998
0.14,0.0 0.547,0.286 0.406,0.286 10 *a
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Disconnect the connector and measure the voltage or resistance according to the value(s) in the table below.

HINT:

The voltage cannot be measured with the connector connected to the skid control ECU (brake actuator assembly) as the connector is watertight.


Standard
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A36-1 (GND1) - Body ground W-B - Body ground Skid control ECU ground Always Below 1 Ω
A36-2 (STP) - Body ground G-W - Body ground Stop light switch input Brake pedal depressed → released 8 to 14 V
→ Below 1.5 V
A36-9 (EXI4)*1 - Body ground G-W - Body ground L4 position switch input
·

Ignition switch ON

·

Transfer shift position not L4


11 to 14 V
A36-12 (+BS) - Body ground W-R - Body ground Solenoid relay power supply Always 11 to 14 V
A36-13 (GND2) - Body ground W-B - Body ground Pump motor ground Always Below 1 Ω
A36-20 (EXI)*1 - Body ground R-B - Body ground 4WD detection switch input
·

Ignition switch ON

·

Transfer shift position H2


11 to 14 V
A36-24 (+BM) - Body ground R - Body ground Motor relay power supply Always 11 to 14 V
A36-27 (FSW+) - Body ground L - Body ground Brake pedal load sensing switch input Brake pedal depressed → released 950 to 1050 Ω → 203 to 223 Ω
A36-28 (EXI3) - Body ground V - Body ground IG power supply Ignition switch ON 11 to 14 V
A36-29 (PKB) - Body ground L-O - Body ground Parking brake switch input
·

Ignition switch ON

·

Parking brake lever pulled → released


Below 1 Ω → 10 kΩ or higher
A36-30 (CSW) - Body ground R-L - Body ground VSC OFF switch input VSC OFF switch held → released Below 1 Ω → 10 kΩ or higher
A36-32 (P)*2 - Body ground G-B - Body ground Park/neutral position switch signal input
·

Ignition switch ON

·

Shift lever not in P → Shift lever in P


Below 1 V
→ 11 to 14 V
A36-34 (IG1) - Body ground B - Body ground ECU power supply Ignition switch ON 11 to 14 V

*1: for 4WD

*2: for Automatic Transmission