Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2011.10–2013.10
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052601 VEHICLE STABILITY CONTROL SYSTEM D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  DTC CHECK / CLEAR  


DTC CHECK/CLEAR (When Using Intelligent Tester)


a.

Check for DTCs.

i.

Turn the ignition switch off.


ii.

Connect the intelligent tester to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the intelligent tester on.


v.

Enter the following menus: Chassis / ABS/VSC/TRC / DTC.


vi.

Check the details of the DTCs.

HINT:

Refer to the intelligent tester operator's manual for further details.




b.

Clear the DTCs.

NOTICE:

Clearing the DTC also clears the freeze frame data.


i.

Turn the ignition switch off.


ii.

Connect the intelligent tester to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the intelligent tester on.


v.

Enter the following menus: Chassis / ABS/VSC/TRC / DTC.


vi.

Clear the DTCs by following the prompts on the intelligent tester.

HINT:

Refer to the intelligent tester operator's manual for further details.





DTC CHECK/CLEAR (When Using SST Check Wire)


a.
C284166
1.625,0.792 1.875,0.292 1.875,0.292 2.042,0.292 true 2.094,1.927 1.938,1.927 1.938,1.927 1.844,1.51 true 2.083,0.229 2.396,0.427 0.313,0.198 10 false CG 0.073,0.042 0.385,0.24 0.313,0.198 10 false *a 2.146,1.844 2.458,2.042 0.313,0.198 10 false TC
*a Front view of DLC3


Check for DTCs.

i.

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  


ii.

Turn the ignition switch to ON.


iii.

Read the DTCs output from the ABS warning light and VSC OFF indicator light in the combination meter.

HINT:
·

When the system is normal, the ABS warning light and VSC OFF indicator light blink at 0.25 second intervals (0.25 seconds on and 0.25 seconds off).

·

When only 1 DTC is output, the light outputs the same code after an interval of 4 seconds. Example: when DTC 21 is output, the light blinks twice, turns off for 1.5 seconds, blinks once, turns off for 4 seconds, and then repeats this output pattern.

·

When 2 or more DTCs are output, the light outputs the codes with an interval of 2.5 seconds between each different code, and it repeats the output of all codes after an interval of 4 seconds.




iv.

Warning and indicator light codes are defined in the following charts.

ABS DTC
ABS Warning Light Display DTC Code
11 C0278
12 C0279
13 C0273
14 C0274
21 C0226
22 C0236
23 C0246
24 C0256
25 C1225
31 C1401
C1405
32 C1402
C1406
33 C1403
C1407
34 C1404
C1408
35 C1413
36 C1414
37 C1337
38 C1415
39 C1416
41 C1241
C1417
43 C1243
44 C1419
C1420
C1442
45 C1245
46 C1421
C1422
C1423
C1424
49 C1425
C1426
51 C1427
C1428
67 C1429
C1430
C1431
68* C1268*
91 C1361
94 U0073
95 U0124
97 C1381

*: for 4WD


VSC DTC
VSC OFF Indicator Light Display DTC Code
31 C1432
C1433
C1434
32 C1232
34 C1435
C1436
C1443
36 C1210
39 C1336
43* -
51 C1201
53 C1203
62 U0123
63 U0126
65 C1437
U0100
66 C1290
C1439
C1445
98 C1440
C1441

*: This DTC is stored when the VSC system detects a malfunction in the ABS.



v.

Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.

HINT:

If 2 or more DTCs are output at the same time, the DTCs are output in ascending order.




b.

Clear the DTCs.

i.
C284166
1.625,0.792 1.875,0.292 1.875,0.292 2.042,0.292 true 2.094,1.927 1.938,1.927 1.938,1.927 1.844,1.51 true 2.083,0.229 2.396,0.427 0.313,0.198 10 false CG 0.073,0.042 0.385,0.24 0.313,0.198 10 false *a 2.146,1.844 2.458,2.042 0.313,0.198 10 false TC
*a Front view of DLC3


Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  


ii.

Turn the ignition switch to ON.


iii.

Clear the DTCs stored in the ECU by depressing the brake pedal 8 times or more within 5 seconds.


iv.

Check that the ABS warning light and VSC OFF indicator light blink at 0.25 second intervals (0.25 seconds on and 0.25 seconds off).


v.

Remove SST from the terminals of the DLC3.




END OF DTC CHECK/CLEAR


a.

Turn the ignition switch to ON.


b.

Check that the ABS warning light and VSC OFF indicator light go off within approximately 3 seconds after turning the ignition switch to ON.