Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL(w/o VSC) › 2012.10–2014.10
RM1840EF _54 Brake _009624 BRAKE SYSTEM (OTHER) _0052608 BRAKE PEDAL(w/o VSC) N

BRAKE SYSTEM (OTHER)  BRAKE PEDAL(w/o VSC)  ADJUSTMENT  


PROCEDURE

Hide 1.CHECK AND ADJUST BRAKE PEDAL HEIGHT

a.
C236936C02
2.271,0.979 2.271,0.271 2.271,0.271 2.073,0.271 false 1.656,1.677 1.552,2.583 1.552,2.583 1.552,2.854 false 1.573,1.646 1.385,2.49 1.385,2.49 1.313,2.49 false 1.875,0.177 2.135,0.458 0.26,0.281 10 false *1 1.135,2.396 1.375,2.615 0.24,0.219 10 false *2 1.479,2.865 1.719,3.094 0.24,0.229 10 false *3 2.333,3.51 2.583,3.76 0.25,0.25 10 false *a
*1 Stop Light Switch
*2 Push Rod
*3 Lock Nut
*a Pedal Height


Check the pedal height.

Pedal Height from Dash Panel:
Model Specified Condition
for Manual Transmission 152.9 to 162.9 mm (6.020 to 6.413 in.)
for Automatic Transmission 154.1 to 164.1 mm (6.067 to 6.461 in.)



b.

Adjust the pedal height.

i.

Disconnect the connector from the stop light switch.


ii.

Remove the switch.


iii.

Loosen the push rod clevis lock nut.


iv.

Adjust the pedal height by turning the push rod.


v.

Tighten the lock nut.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


vi.
C111301C04
0.615,1.188 0.615,1.719 false 2,1.333 2,1.729 false 1.229,0.49 1.229,0.177 1.229,0.177 1.573,0.177 false 1.635,0.073 1.896,0.302 0.26,0.229 10 false *2 1.917,1.74 2.146,1.948 0.229,0.208 10 false *3 0.531,1.729 0.802,1.958 0.271,0.229 10 false *1
*1 Brake Pedal
*2 Adjuster
*3 Stop Light Switch


Insert the switch into the adjuster until it slightly touches the pedal.

NOTICE:

Do not depress the pedal.



vii.
C111302C05
0.51,0.76 0.51,0.104 0.51,0.104 0.917,0.104 false 1.99,1.281 1.99,1.74 false 0.417,1.615 0.656,1.823 0.24,0.208 10 false *a 0.948,0.021 1.24,0.281 0.292,0.26 10 false *1 1.896,1.76 2.229,1.979 0.333,0.219 10 false *2
*1 Shaft
*2 Stop Light Switch
*a 1.5 to 2.5 mm (0.0591 to 0.0984 in.)


Turn the switch a quarter turn clockwise.

Torque:
1.5 N*m (15 kgf*cm, 13 in.*lbf)

or less


NOTICE:

Do not depress the pedal.



viii.

Connect the connector to the switch.


ix.

Check the switch clearance.

Stop light switch clearance:

1.5 to 2.5 mm (0.0591 to 0.0984 in.)




Hide 2.CHECK BRAKE PEDAL FREE PLAY

C111306C04
2.052,1.438 2.302,1.635 0.25,0.198 10 false *a
*a Pedal Free Play


a.

Stop the engine. Depress the pedal several times until there is no vacuum in the booster. Then release the pedal.


b.

Depress the pedal until resistance is felt.


c.

Check the pedal free play by measuring the distance between the position in the previous step and the released position of the pedal.

Pedal free play:

1.0 to 6.0 mm (0.0394 to 0.236 in.)


If the free play is not as specified, check the switch clearance in the next step.

If the free play is as specified, proceed to the "Check Brake Pedal Reserve Distance" procedure.


d.

Check the switch clearance.

Stop light switch clearance:

1.5 to 2.5 mm (0.0591 to 0.0984 in.)


If the clearance is not as specified, adjust the clearance and recheck the pedal free play.

If the clearance is as specified, troubleshoot the brake system and proceed to the "Check Brake Pedal Reserve Distance" procedure.


Hide 3.CHECK BRAKE PEDAL RESERVE DISTANCE

C111339C03
0.885,1.271 0.885,1.667 false 1.458,1.458 1.635,1.656 0.177,0.198 10 false *a 0.802,1.698 1.073,1.927 0.271,0.229 10 false *1
*1 Dash Panel
*a Pedal Reserve Distance


a.

Release the parking brake lever. Start the engine.


b.

Depress the pedal and check the pedal reserve distance.

i.

Depress the pedal with a force of 490 N (50 kgf, 110 lbf).


ii.

Measure the distance between the pedal and dash panel shown in the illustration.

Pedal Reserve Distance:
Item Specified Condition
for 2WD 78.0 mm (2.992 in.)
for 4WD and Pre-Runner for 15 inch Front Disc Brake 85.0 mm (3.347 in.)
for 16 inch Front Disc Brake 76.0 mm (2.992 in.)


If the distance is not as specified, troubleshoot the brake system.