Home › Brake › BRAKE SYSTEM (OTHER) › LOAD SENSING PROPORTIONING VALVE(w/o VSC) › from 2012.10
RM1840EF _54 Brake _009624 BRAKE SYSTEM (OTHER) _0052615 LOAD SENSING PROPORTIONING VALVE(w/o VSC) G

BRAKE SYSTEM (OTHER)  LOAD SENSING PROPORTIONING VALVE(w/o VSC)  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.CHECK LOAD SENSING PROPORTIONING VALVE ASSEMBLY

C283545
2.156,0.563 2.469,0.719 0.313,0.156 10 false *a
*a Weight


a.

Set the vehicle to its curb weight.


b.

Place weights (as necessary) on the rear deck until the rear axle load is as shown below.

Standard Rear Axle Load:
Vehicle Type Specified condition
for 4WD and Pre-Runner except 1GR-FE 9807 N (1000 kgf, 2205 lbf)
for 1GR-FE 10297 N (1050 kgf, 2315 lbf)
for 2WD 8336 N (850 kgf, 1874 lbf)


NOTICE:
·

Be sure that the vehicle is on a level surface before starting the procedure.

·

After placing approximately 60 kg (132 lb) more than the set value, remove weights slowly as necessary so that the load is within +/-15 kg (33 lb) of the adjusted value and there is less than a 25 kg (55 lb) difference between the right and left sides.




c.
F049819
2.385,0.323 2.833,0.323 false 0.771,0.323 1.198,0.323 false 2.875,0.198 3.198,0.396 0.323,0.198 10 false SST 0.396,0.219 0.719,0.417 0.323,0.198 10 false SST

Install SST and bleed air from the brake system.

SST
09709-29018  


d.
F049821
0.124,0.211 0.447,0.412 0.323,0.201 10 SST 2.769,0.211 3.092,0.412 0.323,0.201 10 SST 2.389,0.327 2.733,0.327 false 0.48,0.327 0.687,0.327 false

Raise the front brake fluid pressure to 10000 kPa (107.6 kgf/cm2, 1450 psi) by depressing the brake pedal, and measure the rear brake fluid pressure.

Standard Rear Brake Fluid Pressure:
Vehicle Type Specified Condition
for 4WD and Pre-Runner 4450 +/-490 kPa (45.4 +/-5.0 kgf/cm2, 645 +/-71 psi)
for 2WD 5260 +/-490 kPa (53.6 +/-5.0 kgf/cm2, 762 +/-71 psi)


HINT:
·

The pedal should not be depressed twice or released while raising the front brake fluid pressure.

·

Read the value of the rear brake fluid pressure after raising and holding the front fluid pressure for 2 seconds.



If necessary, adjust the load sensing proportioning valve.


Hide 2.ADJUST LOAD SENSING PROPORTIONING VALVE ASSEMBLY

a.
C111603
0.95,1.911 1.106,2.123 0.156,0.212 10 A

Adjust the length of the No. 2 load sensing spring shackle.

When the rear brake fluid pressure is below the standard pressure, lengthen length A.

When the rear brake fluid pressure is higher than the standard pressure, shorten length A.

Standard Initial Length (A):
Vehicle Type Specified Condition
for 4WD and Pre-Runner 190 mm (7.543 in.)
for 2WD 120 mm (4.764 in.)


Standard Length (A) after Adjustment:
Vehicle Type Specified Condition
for 4WD and Pre-Runner 184 to 196 mm (7.305 to 7.781 in.)
for 2WD 114 to 126 mm (4.526 to 5.002 in.)


HINT:

The rear brake fluid pressure changes according to the table below by adjusting length A.


Standard Pressure Change:
Vehicle Type Specified Condition
for 4WD and Pre-Runner Changes by 120 kPa (1.2 kgf/cm2, 17.6 psi) for every 1 mm (0.0394 in.) change in length A
for 2WD Changes by 140 kPa (1.4 kgf/cm2, 20.5 psi) for every 1 mm (0.0394 in.) change in length A



b.
C111604

If the pressure cannot be adjusted by the No. 2 load sensing spring shackle, loosen the nuts and raise or lower the valve body.

When the pressure is below the standard pressure, lower the load sensing valve assembly.

When the pressure is higher than the standard pressure, raise the load sensing valve assembly.


c.

Tighten the nuts.

Torque:
13 N*m (127 kgf*cm, 9 ft.*lbf)


d.

Adjust the length of the No. 2 load sensing spring shackle again.

HINT:

If the length cannot be adjusted, check the load sensing valve assembly.



Hide 3.CHECK VALVE BODY

a.

Check that the master cylinder rear brake fluid pressure changes according to the rear wheel cylinder pressure.

Standard Pressure:
Vehicle Type Master Cylinder Pressure Wheel Cylinder Pressure
for 4WD and Pre-Runner 2940 kPa (29 kgf/cm2, 428 psi) 1270 +/-200 kPa (13.0 +/-2 kgf/cm2, 185 +/-29 psi)
5880 kPa (59 kgf/cm2, 855 psi) 1720 +/-340 kPa (17.5 +/-3 kgf/cm2, 250 +/-49 psi)
for 2WD 2450 kPa (25 kgf/cm2, 356 psi) 1350 +/-200 kPa (13.8 +/-2 kgf/cm2, 196 +/-29 psi)
5880 kPa (59 kgf/cm2, 855 psi) 2210 +/-340 kPa (22.5 +/-3 kgf/cm2, 321 +/-49 psi)


If the result is not as specified, replace the load sensing valve assembly.