Home › Brake › BRAKE (FRONT) › FRONT BRAKE(for 2WD) › from 2012.10
RM1840EF _54 Brake _009625 BRAKE (FRONT) _0052627 FRONT BRAKE(for 2WD) A

BRAKE (FRONT)  FRONT BRAKE(for 2WD)  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE CYLINDER BOOT

a.
C111363
0.896,0.781 0.917,0.76 false 0.917,0.792 0.927,0.771 false 0.938,0.802 0.958,0.771 false 0.958,0.802 0.979,0.781 false 0.99,0.792 0.979,0.813 false 2.625,1.51 2.646,1.49 false 2.646,1.51 2.656,1.49 false 2.667,1.521 2.677,1.5 false 2.688,1.521 2.698,1.5 false 2.708,1.521 2.719,1.5 false 2.729,1.521 2.74,1.5 false 0.938,0.802 0.938,1.552 false 2.74,1.479 3.021,0.438 3.021,0.438 3.021,0.229 false 3.021,0.229 2.917,0.229 false 2.708,0.146 2.865,0.292 0.156,0.146 10 false *1 0.854,1.583 1,1.719 0.146,0.135 10 false *1
*1 Protective Tape


Using a screwdriver, pry out the set ring and cylinder boot.

HINT:

Tape the screwdriver tip before use.


NOTICE:

Be careful not to damage the brake piston and cylinder.



Hide 2.REMOVE FRONT DISC BRAKE PISTON

a.
C111364
1.229,0.188 1.406,0.354 0.177,0.167 10 false *a 2.938,0.885 3.104,1.031 0.167,0.146 10 false *b 3.104,1.385 3.26,1.542 0.156,0.156 10 false *c
*a 170 mm (6.70 in.)
*b 50 mm (1.97 in.)
*c 30 mm (1.18 in.)


Prepare a wooden plate to hold the pistons.


b.
C111365

Place the wooden plate between the piston and cylinder.


c.

Use compressed air to remove the piston from the cylinder.

CAUTION:

Do not place your fingers in front of the piston when using compressed air.


NOTICE:

Be careful not to spatter the brake fluid.



Hide 3.REMOVE PISTON SEAL

a.
C111366
1.979,1.167 1.958,1.219 false 1.958,1.167 1.938,1.219 false 1.917,1.219 1.927,1.167 false 1.906,1.167 1.896,1.219 false 1.885,1.167 1.885,1.198 false 1.792,1.156 1.771,1.219 false 1.948,1.167 2.573,0.323 2.573,0.323 2.646,0.323 false 2.698,0.24 2.844,0.385 0.146,0.146 10 false *1
*1 Protective Tape


Using a screwdriver, pry out the seal from the cylinder.

HINT:

Tape the screwdriver tip before use.


NOTICE:

Be careful not to damage the inner cylinder and cylinder groove.



Hide 4.REMOVE FRONT DISC BRAKE BLEEDER PLUG CAP

Hide 5.REMOVE FRONT DISC BRAKE BLEEDER PLUG

a.

Remove the bleeder plug from the cylinder.