Home › Brake › BRAKE (REAR) › REAR BRAKE(for 2WD) › from 2012.10
RM1840EF _54 Brake _009626 BRAKE (REAR) _0052632 REAR BRAKE(for 2WD) A

BRAKE (REAR)  REAR BRAKE(for 2WD)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.INSTALL REAR WHEEL BRAKE CYLINDER CUP

C281138
0.51,1.792 0.823,1.948 0.313,0.156 10 *1
*1 Lithium soap base glycol grease


a.

Apply a light coat of lithium soap base glycol grease to 2 new rear wheel brake cylinder cups and 2 pistons.


b.

Install the 2 rear wheel brake cylinder cups to the 2 pistons.


c.

Install the compression spring and 2 pistons to the rear wheel brake cylinder.


d.

Install 2 new cylinder boots to the rear wheel brake cylinder.


Hide 2.TEMPORARILY INSTALL REAR BRAKE DRUM BLEEDER PLUG

a.

Install the rear brake drum bleeder plug to the rear wheel brake cylinder.

HINT:

The rear brake drum bleeder plug will be tightened to a torque specification in the Bleed Brake Line procedures.



b.

Install the bleeder plug cap.


Hide 3.INSTALL REAR WHEEL BRAKE CYLINDER ASSEMBLY LH

a.
C111485

Install the cylinder with the 2 bolts.

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)


b.

Using a union nut wrench, connect the brake line.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



Hide 4.APPLY HIGH-TEMPERATURE GREASE

a.
C238122
0.635,1.844 0.792,1.99 0.156,0.146 10 *1
*1 High-temperature grease


Apply high-temperature grease to the surface of the backing plate which contacts the shoe.


Hide 5.INSTALL REAR BRAKE PARKING BRAKE SHOE LEVER SUB-ASSEMBLY

a.
C236966

Install the rear brake parking brake shoe lever with a new C-washer.


Hide 6.INSTALL REAR BRAKE AUTOMATIC ADJUST LEVER LH

a.
C111489

Install the rear brake automatic adjust lever with the E-ring.


Hide 7.INSTALL REAR BRAKE SHOE

a.

Using needle-nose pliers, connect the No. 3 parking brake cable to the parking brake shoe lever.


b.

Using needle-nose pliers, install the adjust lever tension spring to the automatic adjust lever and rear brake shoe.


c.
C111398
1.927,1.177 2.115,1.177 2.115,1.177 2.115,0.792 false 2.115,0.792 2.448,0.792 false 2.5,0.719 2.813,0.875 0.313,0.156 10 SST

Using SST, install the shoe, pin, shoe hold down spring and shoe hold down spring cup.

SST
09718-00010  


Hide 8.INSTALL PARKING BRAKE SHOE STRUT SET LH

a.
C238123
0.66,1.862 0.821,1.999 0.161,0.138 10 *1
*1 High-temperature grease


Disassemble the parking brake shoe strut set. Apply high temperature grease to the areas indicated by the arrows in the illustration. Then reassemble the parking brake shoe strut set.


b.

Install the rear brake shoe return spring to the parking brake shoe strut set.


c.
C238101
1.303,1.589 1.454,1.731 0.15,0.142 10 *1 1.387,1.206 1.387,1.582 false
*1 Rear Brake Shoe Return Spring


Install the parking brake shoe strut set as shown in the illustration.


Hide 9.INSTALL FRONT BRAKE SHOE

a.
C111397
1.333,1.094 0.469,1.094 0.469,1.094 0.469,1.531 true 0.333,1.542 0.677,1.75 0.344,0.208 10 false SST

Connect the shoe tension spring to the front brake shoe and rear brake shoe.


b.

Using SST, install the shoe, shoe hold down spring and shoe hold down spring cup.

SST
09718-00010  


Hide 10.CONNECT REAR BRAKE SHOE RETURN SPRING

a.

Connect the return spring to the front brake shoe and rear brake shoe.

NOTICE:

Be careful not to damage the wheel cylinder boot.



Hide 11.CHECK REAR BRAKE DRUM INSTALLATION

a.

Check that each part is installed properly.

C115333
1.698,0.26 1.875,0.406 0.177,0.146 10 *A 5.25,0.26 5.427,0.406 0.177,0.146 10 *B 1.396,3.271 1.563,3.417 0.167,0.146 10 *a 5.708,3.26 5.885,3.406 0.177,0.146 10 *a
*A LH Side *B RH Side
*a Front - -



b.
C111493

Measure the inside diameter of the brake drum and diameter of the brake shoes. Check that the difference between the diameters is the correct shoe clearance.

Standard shoe clearance:

0.5 mm (00197 in.)


NOTICE:

There should be no oil or grease on the contact surfaces of the shoe lining and drum.