Home › Steering › POWER ASSIST SYSTEMS › VANE PUMP(for KD Series Engine)
RM1840EF _55 Steering _009628 POWER ASSIST SYSTEMS _0052639 VANE PUMP(for KD Series Engine) G

POWER ASSIST SYSTEMS  VANE PUMP(for KD Series Engine)  INSPECTION  


PROCEDURE

Hide 1.INSPECT CLEARANCE BETWEEN VANE PUMP ROTOR AND VANE PUMP PLATE

a.
R010282
2.333,0.896 2.333,1.771 false 2.271,1.792 2.604,2.063 0.333,0.271 10 false *1
*1 Feeler Gauge


Using a feeler gauge, measure the clearance between the side face of the vane pump rotor groove and the vane pump plates.

Maximum clearance:

0.03 mm (0.00118 in.)


NOTICE:
·

If the clearance is more than the maximum, replace the vane pump plates, vane pump rotor and vane pump cam ring.

·

Refer to the following table to select an appropriate combination of vane pump rotor, vane pump cam ring and vane pump plates.

Combination of Vane Pump Rotor, Vane Pump Cam Ring and Vane Pump Plates:
Vane Pump Rotor Part No. Vane Pump Cam Ring Part No. Vane Pump Plate Part No.
44313-06110 44325-0K010 44345-06110
44313-06120 44325-0K020 44345-06120
44313-06130 44325-0K030 44345-06130
44313-06140 44325-0K040 44345-06140
44313-06150 44325-0K050 44345-06150





Hide 2.INSPECT FLOW CONTROL VALVE

a.
F052069
2.083,0.156 2.271,0.344 0.188,0.188 10 *a
*a Compressed Air


C220818
0.844,0.802 0.844,0.25 0.844,0.25 2.646,0.25 true 2.458,0.813 2.458,0.25 true 2.698,0.198 3.167,0.521 0.469,0.323 10 false *1
*1 Mark


Check the flow control valve for leakage. Close one of the holes and apply compressed air at 392 to 490 kPa (4.00 to 4.99 kgf/cm2, 56.9 to 71.0 psi) to the hole on the opposite side. Confirm that the air does not flow out of the end hole.

NOTICE:

Make sure to use clean and dry air.


If there is leakage, replace the flow control valve.

NOTICE:
·

Check the mark on the front vane pump housing and replace the flow control valve with one having the same mark as that of the front vane pump housing.

·

Refer to the following table to select an appropriate combination of front vane pump housing and flow control valve.

Combination of Front Vane Pump Housing and Flow Control Valve:
Front Vane Pump Housing Mark Flow Control Valve Mark Flow Control Valve Part No.
A A 44330-0K130
B B 44330-0K140
C C 44330-0K150
D D 44330-0K160
E E 44330-0K170
F F 44330-0K180





b.

Coat the flow control valve with power steering fluid.

NOTICE:

Make sure to use new power steering fluid.



c.

Insert the flow control valve into the flow control valve installation hole of the front vane pump housing, and check that the flow control valve enters smoothly under its own weight.

If the flow control valve does not enter the front vane pump housing smoothly, replace the flow control valve.


Hide 3.INSPECT FLOW CONTROL VALVE COMPRESSION SPRING

a.
R008702
2.375,0.969 2.51,1.438 2.51,1.438 2.625,1.438 false 2.698,1.344 3.01,1.552 0.313,0.208 10 false *1
*1 Vernier Caliper


Using a vernier caliper, measure the free length of the flow control valve compression spring.

Minimum free length:

29.2 mm (1.15 in.)


If the length is less than the minimum, replace the flow control valve compression spring.


Hide 4.INSPECT PRESSURE PORT UNION

a.

If the union seat in the pressure port union sub-assembly is severely damaged, replace the pressure port union sub-assembly.