Home › Steering › POWER ASSIST SYSTEMS › VANE PUMP(for 1GR-FE) › from 2012.04
RM1840EF _55 Steering _009628 POWER ASSIST SYSTEMS _0052641 VANE PUMP(for 1GR-FE) A

POWER ASSIST SYSTEMS  VANE PUMP(for 1GR-FE)  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL VANE PUMP HOUSING OIL SEAL

a.

Coat a new vane pump housing oil seal lip with power steering fluid.


b.
F051271
2.271,0.583 1.729,0.49 1.729,0.49 2.104,0.969 true 2.167,1.24 2.063,1.813 true 1.385,0.354 1.75,0.552 0.365,0.198 10 false SST 1.948,1.885 2.229,2.073 0.281,0.188 10 false *1
*1 Oil Seal


Using SST and a press, install a new oil seal.

SST
09950-60010  (09951-00280)
09950-70010  (09951-07100)

NOTICE:

Make sure that the oil seal is installed facing in the correct direction.



Hide 2.INSTALL SHAFT SUB-ASSEMBLY WITH PULLEY

a.
F051272
1.24,0.125 1.51,0.677 true 1.938,0.635 1.24,0.125 1.24,0.125 1.104,0.125 true 0.896,0.031 1.188,0.229 0.292,0.198 10 false *a
*a power steering fluid


Coat the busing inner surface of the front vane pump housing with power steering fluid.


b.

Gradually insert the vane pump shaft.

NOTICE:

Do not damage the vane pump housing oil seal lip in the front vane pump housing.



Hide 3.INSTALL FRONT VANE PUMP SIDE PLATE

a.
F051267

Coat a new O-ring with power steering fluid and install it onto the front vane pump housing.


b.
C065368

Coat a new O-ring with power steering fluid and install it onto the side plate.


c.
F051273

Align the dent of the side plate with that of the front vane pump housing and install the side plate.

NOTICE:

Make sure that the side plate is installed facing in the correct direction.



Hide 4.INSTALL VANE PUMP CAM RING

a.
F051274
1.042,0.25 1.292,0.156 1.292,0.156 1.49,0.156 false 1.552,0.083 1.813,0.271 0.26,0.188 10 false *1
*1 Inscribed Mark


Align the dent of the cam ring with that of the side plate and install the cam ring with the inscribed mark facing outward.


Hide 5.INSTALL VANE PUMP ROTOR

a.
F051275
1.823,0.5 2.406,0.698 true 1.031,0.198 1.219,0.198 1.219,0.198 1.396,0.51 true 0.833,0.104 1.146,0.313 0.313,0.208 10 false *1 2.458,0.625 2.74,0.833 0.281,0.208 10 false *a
*1 Inscribed Mark
*a Round End


Install the vane pump rotor with the inscribed mark facing outward.


b.

Coat the 10 vane plates with power steering fluid.


c.

Install the vane pump rotor with the round ends facing outward.


d.
F051276

Using a snap ring expander, install a new snap ring onto the pulley shaft.


Hide 6.INSTALL REAR VANE PUMP HOUSING

a.

Coat a new O-ring with power steering fluid and install it onto the vane pump housing rear.


b.

Align the straight pin of the vane pump housing rear with the dent of the cam ring, side plate and front vane pump housing, and install the rear vane pump housing with the 4 bolts.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)


Hide 7.INSPECT PRELOAD

a.
C053369

Check that the pump rotates smoothly without making any abnormal noises.


b.

Provisionally install the service bolt.

Recommended service bolt:
Item Specified Condition
Thread Diameter 10 mm (0.3937 in.)
Thread Pitch 1.25 mm (0.0492 in.)
Bolt Length 50 mm (1.9685 in.)



c.

Using a torque wrench, check the pump rotating torque.

Standard rotating torque:

0.27 N*m (2.8 kgf*cm, 2.4 in.*lbf) or less



Hide 8.INSTALL POWER STEERING OIL PRESSURE SWITCH

a.

Coat a new O-ring with power steering fluid and install it onto the power steering oil pressure switch.


b.

Install the power steering oil pressure switch onto the vane pump assembly.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 9.INSTALL FLOW CONTROL VALVE

a.

Coat the compression spring and flow control valve with power steering fluid.


b.
F051277

Install the compression spring and flow control valve.


c.

Coat a new O-ring with power steering fluid and install it onto the pressure port union.


d.

Install the pressure port union.

Torque:
69 N*m (704 kgf*cm, 51 ft.*lbf)


Hide 10.INSTALL POWER STEERING SUCTION PORT UNION

a.

Coat a new O-ring with power steering fluid, and install it onto the suction port union.


b.

Install the suction port union with the bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)