Home › Steering › STEERING COLUMN › STEERING SYSTEM
RM1840EF _55 Steering _009629 STEERING COLUMN _0052642 STEERING SYSTEM N

STEERING COLUMN  STEERING SYSTEM  ADJUSTMENT  


PROCEDURE

Hide 1.ADJUST STEERING CENTER

HINT:

This is the adjustment procedure for when the steering is off center.


a.

Check if the steering wheel is off center.

i.
C178056
1.344,0.781 1.719,0.302 true 1.448,0.979 1.719,0.302 1.719,0.302 1.938,0.302 true 0.844,0.531 0.729,0.333 0.729,0.333 0.615,0.333 true 1.656,1.01 1.844,1.177 1.844,1.177 1.948,1.177 true 0.427,0.229 0.656,0.396 0.229,0.167 10 false *2 2,0.208 2.198,0.385 0.198,0.177 10 false *1 2,1.094 2.26,1.313 0.26,0.219 10 false *3
*1 Masking Tape
*2 Steering Wheel
*3 Steering Column Upper Cover


Apply masking tape to the top center of the steering wheel and steering column upper cover.


ii.

Drive the vehicle in a straight line for 100 m (328 ft.) at a constant speed of 56 km/h (35 mph), and hold the steering wheel to maintain the course.


iii.
C178057
0.938,0.677 0.677,0.469 true 0.927,1.115 0.677,0.469 0.677,0.469 0.458,0.469 true 1.156,0.677 1.344,0.51 true 1.167,1.073 1.344,0.51 1.344,0.51 1.76,0.51 true 1.49,1.063 1.719,1.229 0.229,0.167 10 false *2 0.281,0.375 0.479,0.552 0.198,0.177 10 false *1 1.458,0.24 1.719,0.458 0.26,0.219 10 false *3 1.813,0.427 2.042,0.604 0.229,0.177 10 false *4
*1 Masking Tape
*2 Steering Wheel
*3 Steering Column Upper Cover
*4 Marked Line


Draw a line on the masking tape as shown in the illustration.


iv.

Turn the steering wheel to the center position.

HINT:

Look at the upper surface of the steering wheel, steering spoke and SRS airbag line to find the center position.



v.
C178058
1.01,0.583 0.604,0.396 true 0.875,0.979 0.604,0.396 0.604,0.396 0.479,0.396 true 1.208,0.938 1.385,0.5 true 1.208,0.583 1.375,0.5 1.375,0.5 1.781,0.5 true 1.448,0.854 1.677,1.021 0.229,0.167 10 false *2 0.292,0.302 0.49,0.479 0.198,0.177 10 false *1 1.479,0.229 1.74,0.448 0.26,0.219 10 false *3 1.813,0.406 2.01,0.583 0.198,0.177 10 false *4
*1 Masking Tape
*2 Steering Wheel
*3 Steering Column Upper Cover
*4 Marked Line


Draw a new line on the masking tape on the steering wheel as shown in the illustration.


vi.

Measure the distance between the 2 lines on the masking tape on the steering wheel.


vii.

Convert the measured distance to steering angle.

HINT:
·

Measured distance of 1 mm (0.0394 in.) = Steering angle of approximately 1 degree.

·

Make a note of the steering angle.





b.

Adjust the steering angle.

i.
C283120
1.823,0.729 2,1.219 2,1.219 2.167,0.729 true 1.927,1.292 2.24,1.448 0.313,0.156 10 false *1
*1 Matchmark


Draw a line on the RH and LH tie rod ends and rack ends where it can be easily seen.


ii.

Measure the distance from the RH and LH tie rod ends to the ends of the rack end screws.

HINT:
·

Measure both the RH and LH sides.

·

Make a note of the measured values.




iii.
F051053

Remove the RH and LH boot clips from the rack boots.


iv.

Loosen the RH and LH lock nuts.


v.

Turn the RH and LH rack ends by the same amount (but in different directions) according to the steering angle.

HINT:

One 360 degree turn of the rack ends (1.5 mm (0.0591 in.) horizontal movement) equals 12 degrees of steering angle.



vi.

Tighten the RH and LH lock nuts to the specified torque.

Torque:
56 N*m (571 kgf*cm, 41 ft.*lbf)

NOTICE:

Make sure that the difference between the distances from the RH and LH tie rod ends to the ends of the rack end screws is within 1.0 mm (0.0394 in.).



vii.

Install the RH and LH boot clips.