Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY
RM1840EF _55 Steering _009629 STEERING COLUMN _0052643 STEERING COLUMN ASSEMBLY A

STEERING COLUMN  STEERING COLUMN ASSEMBLY  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



PROCEDURE

Hide 1.REMOVE STEERING SLIDING WITH COUPLING YOKE SUB-ASSEMBLY

a.
G034345
1.5,0.99 1.385,0.167 1.385,0.167 1.302,0.948 true 1.385,0.177 1.188,0.177 true 0.99,0.073 1.292,0.26 0.302,0.188 10 false *1
*1 Matchmark


Place matchmarks on the steering main shaft and yoke.


b.

Remove the bolt and yoke.


Hide 2.REMOVE TRANSPONDER KEY AMPLIFIER (w/ Engine Immobiliser System)

Hide 3.REMOVE KEY CYLINDER LIGHT ASSEMBLY (w/ Key Cylinder Light)

Hide 4.REMOVE STEERING COLUMN UPPER WITH SWITCH BRACKET ASSEMBLY

a.

Using a 3 mm pin punch, mark the center of the 2 tapered-head bolts.


b.

Using a 3 to 4 mm drill bit, drill into the 2 tapered-head bolts.


c.
G034348
2.25,1.125 2.531,1.688 2.531,1.688 2.698,1.688 false 2.75,1.594 2.979,1.781 0.229,0.188 10 false *1
*1 Screw Extractor


Using a screw extractor, remove the 2 bolts and bracket.


Hide 5.REMOVE STEERING COLUMN UPPER CLAMP

Hide 6.REMOVE IGNITION SWITCH LOCK CYLINDER ASSEMBLY

a.

Turn the ignition switch to ACC.


b.
C240927
2.125,0.552 2.01,0.188 2.01,0.188 1.938,0.188 true 0.885,2.583 0.938,2.354 0.938,2.354 0.885,2.354 true 0.969,2.656 1.063,2.906 1.063,2.906 1.115,2.906 true 1.74,0.979 1.958,1.146 0.219,0.167 10 false *a 2.49,2.177 2.781,2.344 0.292,0.167 10 false *b 1.76,0.094 1.958,0.25 0.198,0.156 10 false *1 0.698,2.26 0.927,2.448 0.229,0.188 10 false *2 1.156,2.823 1.385,3.01 0.229,0.188 10 true *3
*1 ACC
*2 Claw
*3 Stopper
*a Push
*b Pull


Insert the tip of a screwdriver into the hole in the steering column upper bracket, as shown in the illustration, and pull the ignition switch lock cylinder out until its claw comes into contact with the stopper of the steering column upper bracket.

NOTICE:

Pull the ignition switch lock cylinder assembly out until its claw comes into contact with the stopper of the steering column bracket assembly upper. Otherwise, the following procedure cannot be conducted properly.



c.
C240347
0.417,0.656 0.208,0.969 0.208,0.969 0.208,1.375 true 0.208,1.365 0.313,1.365 true 0.51,0.688 0.667,1.344 0.667,1.344 0.771,1.344 true 1.688,2.74 1.948,2.927 0.26,0.188 10 false *a 2.875,2.917 3.135,3.104 0.26,0.188 10 false *b 0.813,1.25 1.073,1.438 0.26,0.188 10 false *1 2.125,0.313 2.385,0.5 0.26,0.188 10 false *c 0.333,1.281 0.542,1.469 0.208,0.188 10 true *2
*1 Stopper
*2 Claw
*a Tilt
*b Pull out
*c Claw is detached


Insert the tip of a screwdriver into the hole in the steering column bracket and tilt it downward, as shown in the illustration, to detach the claw of the ignition switch lock cylinder. Then pull out the ignition switch lock cylinder.


Hide 7.REMOVE UNLOCK WARNING SWITCH ASSEMBLY

a.
C283122

Detach the 2 claws and remove the switch.


Hide 8.REMOVE IGNITION SWITCH ASSEMBLY

a.
C283123

Detach the 2 claws and remove the switch from the steering column upper bracket.


Hide 9.REMOVE KEY INTERLOCK SOLENOID (for Automatic Transmission)

a.
G034357

Remove the 2 screws and solenoid from the steering column upper bracket.


Hide 10.REMOVE STEERING MAIN SHAFT ASSEMBLY

a.
G034355

Secure the steering column tube with a vise.


b.

Using a snap ring expander, remove the outer main shaft snap ring.


c.
G034350

Using a brass bar and hammer, tap out the steering main shaft and steering main shaft bearing.

NOTICE:

Be careful not to drop the steering main shaft.



d.
G034349

Using a snap ring expander, remove the inner steering main shaft snap ring.