Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR
RM1840EF _55 Steering _009630 STEERING GEAR / LINKAGE _0052646 STEERING GEAR A

STEERING GEAR / LINKAGE  STEERING GEAR  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1.INSTALL POWER STEERING CYLINDER TUBE OIL SEAL

a.

Install the spacer to the power steering rack housing.

NOTICE:

Do not damage the inside of the power steering rack housing.



b.

Apply power steering fluid to the lip of a new power steering cylinder tube oil seal.


c.
C238631
2.302,2.26 2.198,1.948 2.198,1.948 1.948,1.948 false 2.177,2.563 2.073,1.948 false 0.906,0.708 0.885,0.458 0.885,0.458 0.792,0.458 false 1.656,1.875 2.021,2.052 0.365,0.177 10 false SST 0.5,0.375 0.865,0.552 0.365,0.177 10 false SST

Install the power steering cylinder tube oil seal to the rack housing at an angle.

NOTICE:
·

Make sure that the power steering cylinder tube oil seal is installed in the correct direction as shown in the illustration.

·

Install the power steering cylinder tube oil seal at an angle of approximately 20° so that the lowermost part comes to the point indicated by the arrow in the illustration to prevent damage to the oil seal when it passes the 2 ports.

·

After passing both ports, proceed by pressing the oil at an angle of 10° and 0° sequentially.




d.

Using SST, push in the power steering cylinder tube oil seal until the oil seal passes the 2 ports.

SST
09631-00200  
09950-70010  (09951-07360)

NOTICE:
·

Do not turn SST when inserting the oil seal.

·

Do not use any tools other than SST.




e.

Install SST (09631-00200) to SST (09951-07360) upside down.

SST
09631-00200  
09950-70010  (09951-07360)


f.

Using SST, push the power steering cylinder tube oil seal so that it is level.

SST
09631-00200  
09950-70010  (09951-07360)

NOTICE:

Do not use any tools other than SST.



g.
C238633
2.521,0.51 3.042,0.75 3.042,0.75 3.042,1.792 true 3.042,1.792 2.948,1.792 false 3.042,1.042 2.75,0.938 true 0.854,0.354 0.74,0.24 0.74,0.24 0.656,0.24 false 2.656,1.719 3.021,1.896 0.365,0.177 10 false SST 0.365,0.167 0.729,0.344 0.365,0.177 10 false SST

Using SST and a press, install the power steering cylinder tube oil seal.

SST
09631-00200  
09950-70010  (09951-07360)

HINT:

Press the cylinder tube oil seal until it sits on the stopper portion.



Hide 2.INSTALL "TEFLON" RING

a.

Coat a new O-ring with power steering fluid and install it to the steering rack.


b.
C003629

Stretch a new "Teflon" ring with your fingers.

NOTICE:

Be careful not to overstretch the "Teflon" ring.



c.

Coat the "Teflon" ring with power steering fluid.


d.
C282172

Install the "Teflon" ring to the groove of the steering rack. Grip the ring to press it into the groove.


Hide 3.INSTALL POWER STEERING RACK

a.
C282173
1.823,0.99 2.125,0.49 2.125,0.49 2.385,0.49 true 2.438,3.563 2.594,3.115 2.594,3.115 2.854,3.115 true 2.448,0.406 2.76,0.563 0.313,0.156 10 false *1 2.917,3 3.375,3.198 0.458,0.198 10 false SST
*1 Rack Teeth End


Apply grease to the rack teeth ends.


b.

Install SST to the steering rack.

SST
09631-00350  

HINT:

If necessary, scrape the burrs off the rack teeth ends and burnish them.



c.

Coat SST with power steering fluid.


d.

Install the steering rack to the rack housing.


e.

Remove SST.


f.

Install a new bush to the steering rack.


g.
C282175
2.188,1.281 2.031,1.781 2.031,1.781 1.844,1.781 true 2.5,1.063 2.656,0.448 2.656,0.448 2.865,0.448 true 1.604,1.698 1.917,1.854 0.313,0.156 10 false *1 2.906,0.344 3.365,0.542 0.458,0.198 10 false SST
*1 Oil Seal


Coat SST with power steering fluid.

SST
09631-00350  


h.

Install SST to the opposite end of the steering rack.


i.

Coat the lip of a new oil seal with power steering fluid. Using SST, install the oil seal to the steering rack.

NOTICE:
·

Slide SST and the oil seal straight without tilting them.

·

Make sure that the oil seal is facing the correct direction.

·

Be careful not to damage the lip of the oil seal.




j.

Remove SST.


Hide 4.INSTALL CYLINDER END STOPPER

a.

Apply sealant to the stopper.


b.
ZX00351

Using a wooden block and hammer, tap in the stopper until it is securely installed.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



c.
F043535
1.771,0.427 2.333,0.135 2.333,0.135 2.51,0.135 true 2.563,0.063 2.875,0.229 0.313,0.167 10 false SST

Using SST, tighten the stopper.

SST
09631-20120  

Torque:
83 N*m (841 kgf*cm, 61 ft.*lbf)


Hide 5.TEST AIRTIGHTNESS

a.
C131750
1.719,0.729 1.865,0.125 1.865,0.125 2.052,0.125 true 2.104,0.052 2.458,0.219 0.354,0.167 10 false SST

Install SST to the unions of the rack housing.

SST
09631-12071  (09633-00010)


b.

Apply 53 kPa (400 mmHg, 15.75 in.Hg) of vacuum for about 30 seconds.


c.

Check that there is no change in the vacuum.

If there is a change in the vacuum, check the installation of the oil seals.


Hide 6.INSTALL POWER STEERING CONTROL VALVE

a.
G035022
0.25,1.385 0.115,1.479 0.115,1.479 0.115,1.813 true 0.115,1.813 0.25,1.813 false 0.271,1.719 0.458,1.885 0.188,0.167 10 false *a
*a Apply Molybdenum Disulfide Lithium Base Grease


Apply molybdenum disulfide lithium base grease to the needle roller bearing inside the rack housing shown in the illustration.

Volume of grease applied:

Approximately 2 g (0.07 oz)



b.
F043545

Using a plastic-faced hammer and sliding handle, lightly tap in 2 new union seats.

NOTICE:

Before installing the union seat, remove any adhering to the control valve housing.



c.
C131687

Install a new control valve gasket and the control valve with the 2 bolts.

Torque:
18 N*m (185 kgf*cm, 13 ft.*lbf)


d.
G035024
2.875,0.135 3.208,0.135 false 3.208,0.135 3.208,0.604 false 3.208,0.604 2.813,0.688 true 2.708,0.052 2.885,0.219 0.177,0.167 10 false *a
*a Grease Filling


Apply MP grease as shown in the illustration.


Hide 7.INSTALL RACK GUIDE

a.

Install the rack guide and spring.


b.

Apply sealant to 2 or 3 threads of the spring cap.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



c.
C280976
1.115,0.698 1.26,0.698 1.26,0.698 1.427,1.115 true 0.938,0.625 1.25,0.781 0.313,0.156 10 false *1
*1 12 mm Socket Wrench


Using a 12 mm socket wrench, temporarily install the spring cap.


Hide 8.ADJUST TOTAL PRELOAD

a.

To prevent the steering rack teeth from damaging the lip of the oil seal, temporarily install the RH and LH rack ends.


b.

Using a 12 mm socket wrench, tighten the spring cap.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


c.
C280942
1.125,0.729 1.313,0.729 1.313,0.729 1.438,1.146 true 0.969,0.656 1.281,0.813 0.313,0.156 10 false *1
*1 12 mm Socket Wrench


Loosen the spring cap 30°.


d.
C282176
1.406,0.5 1.146,0.219 1.146,0.219 0.948,0.219 false 0.615,0.115 1.073,0.313 0.458,0.198 10 false SST

Using SST, turn the control valve shaft right and left 1 or 2 times. The rack end will move in and out.

SST
09616-00011  


e.

Loosen the spring cap until the rack guide spring does not function.


f.
C239650
2.469,1.333 2.031,1.333 2.031,1.333 1.677,1.656 true 2.625,0.521 2.438,0.521 2.438,0.521 2.26,0.677 true 2.51,1.271 2.76,1.458 0.25,0.188 10 false *1 2.656,0.458 2.979,0.615 0.323,0.156 10 false SST
*1 12 mm Socket Wrench


Using SST, a torque wrench and a 12 mm socket wrench, tighten the spring cap until the preload is within the specification.

SST
09616-00011  

Standard preload (turning):

1.0 to 1.8 N*m (11 to 18 kgf*cm, 9 to 15 in.*lbf)


NOTICE:

Perform adjustments by tightening the spring cap. Do not loosen the spring cap.



g.

Apply sealant to 2 or 3 threads of the lock nut.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



h.

Temporarily install the lock nut.


i.
C239841
1.594,0.958 1.844,0.229 1.844,0.229 1.938,0.229 true 1.292,1.396 1.198,1.885 1.198,1.885 1.073,1.885 true 1.969,0.156 2.292,0.323 0.323,0.167 10 false SST 0.875,1.802 1.104,1.958 0.229,0.156 10 false *1 0.104,0.719 0.333,0.875 0.229,0.156 10 false *a 3.063,1.302 3.292,1.458 0.229,0.156 10 false *b
*1 12 mm Socket Wrench
*a Hold
*b Turn


Using a 12 mm socket wrench, hold the spring cap. Using SST, tighten the lock nut.

SST
09922-10010  

Torque:
without SST : 69 N*m (700 kgf*cm, 51 ft.*lbf)
with SST : 51 N*m (516 kgf*cm, 37 ft.*lbf)

HINT:
·

Use a torque wrench with a fulcrum length of 345 mm (13.58 in.).

·

The torque value for use with SST is effective when SST is parallel to the torque wrench.




j.
C282177
1.906,0.49 1.76,0.271 1.76,0.271 1.552,0.271 false 1.208,0.167 1.667,0.365 0.458,0.198 10 false SST

Using SST, recheck the total preload.

SST
09616-00011  

Standard preload (turning):

1.0 to 1.8 N*m (11 to 18 kgf*cm, 9 to 15 in.*lbf)



k.

Remove the RH and LH rack ends.


Hide 9.INSPECT POWER STEERING RACK

a.
G038615

Insert a wire 20 mm (0.787 in.) into the vent hole of the steering rack, and make sure that the vent hole is not clogged with grease.

NOTICE:

If the hole is clogged, the pressure inside the boot will change after the boot is assembled and the steering wheel is turned.



Hide 10.INSTALL STEERING RACK END SUB-ASSEMBLY

a.
C058310

Install a new claw washer to each steering rack end while aligning the claw of the claw washer with the notch on the steering rack end.


b.

Temporarily install the 2 steering rack ends to the power steering rack.


c.

Fill up the ball joint of each steering rack end with MP grease.


d.

Using SST, install the power steering rack end (RH side) to the power steering rack.

SST
09922-10010  

C280993
2.646,1.177 2.771,0.896 2.771,0.896 2.927,0.896 false 0.99,2.031 1.125,2.031 1.125,2.031 1.26,1.813 true 5.083,2.5 5.229,2.5 5.229,2.5 5.302,2.229 true 5.292,1.552 5.188,1.219 5.188,1.219 5.063,1.219 false 0.458,0.25 0.771,0.406 0.313,0.156 10 false *A 4.021,0.281 4.333,0.438 0.313,0.156 10 false *B 4.906,2.417 5.219,2.573 0.313,0.156 10 false *1 2.24,2.01 2.552,2.167 0.313,0.156 10 false *a 2,0.792 2.313,0.948 0.313,0.156 10 false *b 2.99,0.802 3.448,1 0.458,0.198 10 false SST 0.688,1.938 1.146,2.135 0.458,0.198 10 false SST 5.333,1.146 5.646,1.302 0.313,0.156 10 false *b 4.76,1.125 5.219,1.323 0.458,0.198 10 false SST
*A for RH Side *B for LH Side
*1 Wrench - -
*a Hold *b Turn


Torque:
without SST : 103 N*m (1050 kgf*cm, 76 ft.*lbf)
with SST : 75 N*m (765 kgf*cm, 55 ft.*lbf)

HINT:
·

Rotate SST in the direction shown in the illustration.

·

Use a torque wrench with a fulcrum length of 345 mm (13.6 in.).




e.

Using SST and a wrench, install the power steering rack end (LH side) to the power steering rack.

SST
09922-10010  

Torque:
without SST : 103 N*m (1050 kgf*cm, 76 ft.*lbf)
with SST : 75 N*m (765 kgf*cm, 55 ft.*lbf)

HINT:
·

Rotate SST in the direction shown in the illustration.

·

Use a torque wrench with a fulcrum length of 345 mm (13.6 in.).




f.
C035928
1.688,0.75 1.51,1.792 1.51,1.792 1.365,1.792 true 1.198,1.719 1.438,1.885 0.24,0.167 10 false *1
*1 Brass Bar


Using a brass bar and hammer, stake the 2 claw washers (LH and RH side).

NOTICE:

Do not strike the steering rack.



Hide 11.INSTALL STEERING RACK BOOT LH

a.

Install the boot.

NOTICE:

Be careful not to damage or twist the boot.



Hide 12.INSTALL STEERING RACK BOOT RH

HINT:

Use the same procedure described for the LH side.


Hide 13.INSTALL STEERING RACK BOOT CLAMP LH

a.
G102163
0.896,0.208 1.052,0.406 0.156,0.198 10 A

Using SST, install a new rack boot clamp as shown in the illustration.

SST
09240-00020  
09521-24010  

Standard clearance (A):

3.0 mm (0.118 in.) or less


NOTICE:

Be careful not to damage the boot.



Hide 14.INSTALL STEERING RACK BOOT CLAMP RH

HINT:

Use the same procedure described for the LH side.


Hide 15.INSTALL STEERING RACK BOOT CLIP LH

a.

Using pliers, install the clip.


Hide 16.INSTALL STEERING RACK BOOT CLIP RH

HINT:

Use the same procedure described for the LH side.


Hide 17.INSPECT POWER STEERING LINK ASSEMBLY

Hide 18.INSTALL STEERING TURN PRESSURE TUBE

a.

Apply power steering fluid to 4 new O-rings, and install the O-rings to the turn pressure tubes.


b.

Using a union nut wrench, install the 2 turn pressure tubes.

Torque:
13 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



Hide 19.INSTALL TIE ROD END SUB-ASSEMBLY LH

a.

Screw the lock nut and tie rod end onto the rack end until the matchmarks are aligned.


b.

After adjusting the toe-in, tighten the nut.

Torque:
56 N*m (571 kgf*cm, 41 ft.*lbf)


Hide 20.INSTALL TIE ROD END SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.