Home › Audio / Visual / Telematics › AUDIO / VIDEO › FRONT DOOR SPEAKER › from 2012.10
RM1840EF _56 Audio / Visual / Telematics _009631 AUDIO / VIDEO _0052648 FRONT DOOR SPEAKER A

AUDIO / VIDEO  FRONT DOOR SPEAKER  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.INSTALL FRONT NO. 1 SPEAKER ASSEMBLY

a.

Install a nose piece to an air riveter or hand riveter. Then insert the mandrel part of a new φ4 mm waterproof rivet into the nose piece.


b.
E225838

Using an air riveter or hand riveter, install the front No. 1 speaker assembly with 3 new rivets.

NOTICE:
·
B171664
1.229,1.104 1.083,1.635 1.083,1.635 1.24,2.198 false 1.083,1.635 0.813,1.635 false 1.792,0.896 2.031,1.635 2.031,1.635 1.771,2.531 false 2.031,1.635 2.313,1.635 false 2.26,0.604 2.521,0.802 0.26,0.198 10 *a 2.26,2.448 2.563,2.677 0.302,0.229 10 *b 2.344,1.563 2.594,1.781 0.25,0.219 10 *1 0.594,1.573 0.844,1.75 0.25,0.177 10 *2
*1 Mandrel
*2 Riveter
*a INCORRECT
*b CORRECT


Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

·
B172390
0.719,0.104 1.021,0.104 false 0.823,1.146 1.021,1.146 false 0.823,2.438 1.021,2.438 false 2.313,0.573 2.542,0.781 0.229,0.208 10 *a 2.313,2.76 2.552,2.958 0.24,0.198 10 *b 1.052,2.365 1.313,2.583 0.26,0.219 10 *1 2.323,1.573 2.583,1.781 0.26,0.208 10 *a 1.052,1.073 1.292,1.25 0.24,0.177 10 *1 1.052,0.021 1.302,0.219 0.25,0.198 10 *1
*1 Riveter
*a INCORRECT
*b CORRECT


Confirm that the rivets are seated properly against the speaker.

·

Do not tilt the riveter when installing the rivet to the speaker.

·

Do not leave any space between the rivet head and speaker.

·
B172391
0.74,0.646 0.938,0.646 false 0.729,2.156 0.938,2.156 false 2.292,1.042 2.615,1.271 0.323,0.229 10 *a 2.302,2.458 2.625,2.667 0.323,0.208 10 *b 0.958,0.552 1.229,0.719 0.271,0.167 10 *1 0.958,2.073 1.271,2.24 0.313,0.167 10 *1
*1 Riveter
*a INCORRECT
*b CORRECT


Do not leave any space between the speaker and door. Firmly hold together the 2 items while installing the rivet.




c.

Connect the connector.


Hide 2.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

Hide 3.INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (w/ Power Window)

Hide 5.INSTALL FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

Hide 6.INSTALL FRONT NO. 2 SPEAKER ASSEMBLY

a.

Install the front No. 2 speaker assembly with the screw.


b.

Connect the connector.


Hide 7.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH

Hide 8.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).