Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › 2011.10–2012.01
RM1840EF _56 Audio / Visual / Telematics _009631 AUDIO / VIDEO _0052657 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Radio Receiver Power Source Circuit  


DESCRIPTION

This circuit provides power to the radio and display receiver assembly.

WIRING DIAGRAM

C240233
5.271,3.104 6.458,3.604 1.188,0.5 10 false Radio and Display Receiver Assembly 5.521,0.771 5.792,1.031 0.271,0.26 10 false B 5.521,1.948 5.917,2.156 0.396,0.208 10 false IG 5.521,2.521 5.948,2.708 0.427,0.188 10 false GND 5.521,1.354 5.958,1.604 0.438,0.25 10 false ACC 5.177,2.333 5.365,2.5 0.188,0.167 10 false 7 5.052,2.531 5.448,2.719 0.396,0.188 10 false G129 5.177,1.75 5.292,1.917 0.115,0.167 10 false 1 5.052,1.948 5.458,2.104 0.406,0.156 10 false G127 5.052,0.781 5.438,1 0.385,0.219 10 false G129 5.177,0.573 5.292,0.74 0.115,0.167 10 false 4 5.177,1.167 5.292,1.333 0.115,0.167 10 false 3 2.813,1.219 3.167,1.396 0.354,0.177 10 false ACC 2.813,0.625 3.333,0.802 0.521,0.177 10 false RAD 0.781,0.771 1.698,1.052 0.917,0.281 10 false from Battery 0.781,1.292 1.698,1.708 0.917,0.417 10 false from Ignition Switch 5.052,1.365 5.479,1.625 0.427,0.26 10 false G129

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER - BATTERY AND BODY GROUND)
a.
C240234
0.49,0.885 0.917,1.167 0.427,0.281 0.281,2.396 0.708,2.677 0.427,0.281 1.99,0.833 2.281,0.615 2.281,0.615 2.448,0.615 true 2.146,0.958 2.427,1.26 2.427,1.26 2.542,1.26 true 1.688,1.156 1.365,1.531 1.365,1.531 1.26,1.531 true 1.031,2.563 1.583,3.115 1.583,3.115 1.698,3.115 true 0.104,0.073 0.417,0.229 0.313,0.156 10 false *a 0.531,0.948 0.979,1.177 0.448,0.229 10 false G129 0.333,2.458 0.781,2.688 0.448,0.229 10 false G127 0.927,1.448 1.375,1.677 0.448,0.229 10 false GND 2.604,1.188 3.052,1.417 0.448,0.229 10 false B 2.49,0.542 2.938,0.771 0.448,0.229 10 false ACC 1.76,3.042 2.208,3.271 0.448,0.229 10 false IG
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the G129 and G127 radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G129-7 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G129-4 (B) - Body ground Always 11 to 14 V
G129-3 (ACC) - Body ground Ignition switch ACC
G127-1 (IG) - Body ground Ignition switch ON



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR