Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2012.01–2012.04
RM1840EF _56 Audio / Visual / Telematics _009632 NAVIGATION / MULTI INFO DISPLAY _0052661 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Illumination Circuit  


DESCRIPTION

Power is supplied to the navigation receiver assembly and steering pad switch assembly illumination when the light control switch is in the TAIL or HEAD position.

WIRING DIAGRAM

C240176
4.156,5.948 5.135,6.396 0.979,0.448 10 false Spiral Cable Sub-assembly 1.219,5.969 3.177,6.24 1.958,0.271 10 false Steering Pad Switch Assembly 0.771,0.406 2.021,0.698 1.25,0.292 10 false from Taillight Relay 0.823,3.75 1.417,3.969 0.594,0.219 10 false LH Side 5.771,4.656 5.948,4.833 0.177,0.177 10 false 7 5.729,3.135 5.906,3.313 0.177,0.177 10 false 23 5.708,1.5 5.885,1.677 0.177,0.177 10 false 10 4.875,3.24 5.052,3.417 0.177,0.177 10 false 4 3.979,3.24 4.156,3.417 0.177,0.177 10 false 8 4.833,1.583 5.01,1.76 0.177,0.177 10 false 12 5.625,1.688 6.021,1.906 0.396,0.219 10 false G105 5.625,3.344 6.042,3.583 0.417,0.24 10 false G152 5.625,4.865 6.021,5.052 0.396,0.188 10 false G105 4.156,5.781 4.448,5.938 0.292,0.156 10 false G12 1.219,5.802 1.51,5.958 0.292,0.156 10 false z3 1.188,4.438 1.635,4.656 0.448,0.219 10 false DISP 0.979,3.24 1.792,3.417 0.813,0.177 10 false On/Off Hook 1.146,2.844 1.594,3.021 0.448,0.177 10 false MODE 6.063,4.865 6.49,5.094 0.427,0.229 10 false GND 6.063,3.344 6.479,3.625 0.417,0.281 10 false SWG 6.083,1.688 6.531,1.896 0.448,0.208 10 false ILL+ 4.323,3.229 4.75,3.406 0.427,0.177 10 false EAU 4.333,1.583 4.76,1.76 0.427,0.177 10 false IL+2 1.156,2.365 1.583,2.542 0.427,0.177 10 false Seek 1.229,1.865 1.813,2.042 0.583,0.177 10 false Vol 3.969,1.583 4.146,1.76 0.177,0.177 10 false 5 5.865,5.896 7.135,6.365 1.271,0.469 10 false Navigation Receiver Assembly 0.813,5.125 1.427,5.365 0.615,0.24 10 false RH Side

CAUTION / NOTICE / HINT

CAUTION:

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the SRS (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the navigation receiver assembly, steering pad switch assembly, glove box or other parts (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the HEAD or TAIL position.

Result:
Result Proceed to
Illumination comes on for all components except steering pad switch assembly. A
Illumination comes on for all components except navigation receiver assembly. B
No illumination comes on (navigation receiver assembly, hazard switch, glove box, etc.). C




A

2.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BATTERY)

B

6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)

C

2.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BATTERY)
a.
E198671
1.448,0.375 1.896,0.646 0.448,0.271 2.052,1.635 2.479,1.74 true 0.125,0.073 0.604,0.271 0.479,0.198 10 false *a 1.542,0.438 1.844,0.635 0.302,0.198 10 false G12 2.531,1.656 2.865,1.823 0.333,0.167 10 false IL+2
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)


Disconnect the G12 spiral cable sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G12-12 (IL+2) - Body ground Light control switch TAIL or HEAD 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL

C237720
3.344,0.042 3.781,0.25 0.438,0.208 2.917,0.594 3,0.594 3,0.594 3.542,0.833 true 2.917,0.24 3,0.24 3,0.24 3.688,0.76 true 2.594,0.531 2.958,0.729 0.365,0.198 10 false EAU 2.604,0.156 2.969,0.354 0.365,0.198 10 false IL+2 3.49,0.063 3.854,0.26 0.365,0.198 10 false z3


b.

Connect the positive (+) lead of the battery to terminal z3-5 (IL+2) and the negative (-) lead to terminal z3-8 (EAU) of the steering pad switch assembly connector.


c.

Check if the illumination for the steering pad switch assembly comes on.

OK:

Illumination for the steering pad switch assembly comes on.



Result:
Proceed to
OK
NG



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL

C282256
1.802,0.927 1.719,0.615 true 2.188,0.958 1.927,0.719 true 5.615,2.417 5.281,1.948 true 5.219,2.406 5.135,2.052 true 1.333,0.188 1.646,0.385 0.313,0.198 10 false *a 4.635,1.49 4.948,1.688 0.313,0.198 10 false *b 1.792,0.948 2.104,1.146 0.313,0.198 10 false IL+2 2.229,0.948 2.542,1.146 0.313,0.198 10 false EAU 5.208,2.438 5.521,2.635 0.313,0.198 10 false EAU 5.594,2.438 5.906,2.635 0.313,0.198 10 false IL+2
*a Steering Pad Switch Side *b Vehicle Side



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
8 (EAU) - 4 (EAU) Spiral cable is turned 2.5 rotations counterclockwise Below 1 Ω
Spiral cable is centered
Spiral cable is turned 2.5 rotations clockwise
5 (IL+2) - 12 (IL+2) Spiral cable is turned 2.5 rotations counterclockwise
Spiral cable is centered
Spiral cable is turned 2.5 rotations clockwise


CAUTION:

The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the Precaution for the SRS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY)
a.

Disconnect the G152 navigation receiver assembly connector.


b.

Disconnect the G12 spiral cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G152-23 (SWG) - G12-4 (EAU) Always Below 1 Ω
G152-23 (SWG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
E178447
1.438,0.417 1.948,0.708 0.51,0.292 2.104,1.375 2.448,1.771 true 1.594,1.375 1.24,1.771 true 0.167,0.115 0.344,0.271 0.177,0.156 10 false *a 2.51,1.729 2.885,1.885 0.375,0.156 10 false ILL+ 1.531,0.49 1.958,0.698 0.427,0.208 10 false G105 0.917,1.729 1.292,1.885 0.375,0.156 10 false GND
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


Disconnect the G105 navigation receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G105-7 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G105-10 (ILL+) - Body ground Light control switch TAIL or HEAD 11 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR