Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2012.01–2012.04
RM1840EF _56 Audio / Visual / Telematics _009632 NAVIGATION / MULTI INFO DISPLAY _0052661 NAVIGATION SYSTEM D

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  DTC CHECK / CLEAR  


START DIAGNOSTIC MODE


HINT:
·

Illustrations may differ from the actual vehicle depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle.

·

If the system cannot enter the diagnostic mode, replace the navigation receiver assembly (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION RECEIVER>REMOVAL).



a.

There are 2 methods to start diagnostic mode. Start the mode by using one of them.


b.

Method 1

i.

Start the engine.


ii.
E234519

Press the "MENU" switch.


iii.
E237752
0.952,0.787 1.104,0.787 false 1.12,0.711 1.274,0.854 0.154,0.144 10 *a 0.952,1.345 1.104,1.345 false 1.12,1.269 1.274,1.412 0.154,0.144 10 *b
*a Upper left
*b Lower left


From the display quality adjustment screen, touch the corners of the screen in the following order: upper left → lower left → upper left → lower left → upper left → lower left.


iv.

The diagnostic mode starts and the "System Check Mode" screen will be displayed. Service inspection starts automatically and the result will be displayed.



c.

Method 2

i.
E234519

While pressing and holding the "MENU" switch, operate the light control switch: off → turn on → turn off → turn on → turn off → turn on → turn off.


ii.
E237753

Diagnostic mode starts and the "Service Menu" screen is displayed.




FINISH DIAGNOSTIC MODE


a.

There are 2 methods to end diagnostic mode. Use one of them.

i.

Turn the ignition switch off.


ii.

Press and hold the "MENU" switch for 3 seconds.




FAILURE DIAGNOSIS


a.
E237754

Touch the "Failure Check" button on the "Service Menu" screen.


b.
E237755

The "Failure Check" screen is displayed.



SYSTEM CHECK


a.
E237756

Touch the "System Check" button on the "Failure Check" screen.


b.
E237757

The "System Check Mode" screen is displayed.



CHECK DTC (CHECK USING SYSTEM CHECK MODE SCREEN)


a.
E238675
0.896,0.719 1.271,0.896 0.375,0.177 2.188,1.219 2.563,1.396 0.375,0.177 0.583,0.75 0.865,0.875 0.281,0.125 0.583,0.823 0.417,0.823 true 1.094,0.896 1.094,1.865 true 2.021,1.74 2.021,1.865 true 2.573,1.74 2.573,1.865 true 2.563,1.333 3.031,1.333 true 0.24,0.74 0.385,0.885 0.146,0.146 10 false *a 1.01,1.875 1.156,2.021 0.146,0.146 10 false *b 1.927,1.875 2.073,2.021 0.146,0.146 10 false *c 2.49,1.875 2.635,2.021 0.146,0.146 10 false *d 3.042,1.26 3.188,1.406 0.146,0.146 10 false *e

System check mode screen description

Screen Description
Display Content
*a: Device Name List No. 1
·

Device Name List No. 1 displays some of the devices that make up the audio visual system.

·

The names of the components from Device Name List No. 1 are shown in the following table.


*b: Check Result Result codes for all devices are displayed.
*c: Memory Clear
·

Present and history DTCs and registered connected device names are cleared.

·

Press the "Memory CLR" switch for 3 seconds.


*d: Recheck
·

A system check will be performed again after the memory is cleared.

·

The "Recheck" switch will dim during a system check.


*e: Device Name List No. 2
·

Device Name List No. 2 displays some of the devices that make up the audio and visual system.

·

The names of the components from Device Name List No. 2 are shown in the following table.



*a: Device Name List No. 1 Description
Name Component Connection Method
AVN Navigation receiver assembly -

*b: Check Result Description
Result Meaning Action
DETAIL The device responds with a DTC. Look up the DTC in "Unit Check Mode"
OK Displayed when there are no problems. -
NRES Displayed when the device does not respond. -
NCON Displayed when the device is not connected. -

*e: Device Name List No. 2 Description
Name Component Connection Method
AUX No. 1 stereo jack adapter assembly Vehicle wire harness


b.
E237759
0.698,0.667 1.073,0.781 0.375,0.115 0.74,0.823 1.073,1.177 0.333,0.354 1.271,0.688 1.646,0.792 0.375,0.104 1.417,0.438 1.417,0.104 1.417,0.104 1.448,0.104 true 1.625,0.688 1.625,1.844 true 0.698,0.74 0.375,0.74 true 0.906,1.177 0.906,1.854 true 2.594,1.74 2.594,1.844 true 1.458,0.021 1.604,0.167 0.146,0.146 10 false *a 0.198,0.656 0.344,0.802 0.146,0.146 10 false *c 1.542,1.865 1.688,2.01 0.146,0.146 10 false *b 0.823,1.865 0.969,2.01 0.146,0.146 10 false *d 2.521,1.854 2.667,2 0.146,0.146 10 false *e

Unit check mode screen description

Screen Description
Display Content
*a: Device name Target device
*b: History DTC Diagnostic memory results and stored DTCs are displayed.
*c: Current DTC DTCs output in the service check are displayed.
*d: DTC DTC (Diagnostic Trouble Code)
*e: Diagnosis clear switch Pushing this switch for 3 seconds clears the diagnostic memory data of the target device (both the response to the diagnostic system check result and the displayed data are cleared).

HINT:
·

This screen is updated once per second.

·

A maximum of 6 DTCs can be displayed for history and present DTCs.




c.
E237758

Read the system check result.


d.

If the check result is "DETAIL", touch the displayed check result.


e.
E237759
0.917,1.188 1.229,1.948 1.229,1.948 1.49,1.052 true 1.146,1.979 1.292,2.125 0.146,0.146 10 false *a
*a Diagnostic Code


View the results on the "Unit Check Mode" screen and record them.


f.
E237760

When proceeding to view the results of another device, touch the "Back" button to return to the "System Check Mode" screen.

HINT:

To check the other items, repeat this procedure from the first step.




DTC CLEAR/RECHECK (CLEAR USING SYSTEM CHECK MODE SCREEN)


a.

Clear DTC

i.
E237761

Touch the "code CLR" button for 3 seconds.


ii.

Confirm that the check results are cleared.

HINT:
·

To clear the DTC for a specific device, clear the DTC using the "Unit Check Mode" screen.

·

When clearing a DTC using the "Unit Check Mode" screen, touch the "Code CLR" button for 3 seconds.





b.

Recheck

i.
E237762

Touch the "Recheck" button.


ii.
E237763

Confirm that all check results are "OK" when the check results are displayed. If a result other than "OK" is displayed, troubleshoot again.

HINT:

When a DTC is cleared using the "Unit Check Mode" screen, touch the "Back" button to return to the "System Check Mode" screen and perform this operation.