Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2012.01–2012.04
RM1840EF _56 Audio / Visual / Telematics _009632 NAVIGATION / MULTI INFO DISPLAY _0052661 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Navigation Receiver Assembly Power Source Circuit  


DESCRIPTION

This circuit provides power to the navigation receiver assembly.

WIRING DIAGRAM

C240172
5.25,3.083 6.531,3.438 1.281,0.354 10 false Navigation Receiver Assembly 5.552,0.833 5.688,1 0.135,0.167 10 false B 5.552,2.302 5.938,2.469 0.385,0.167 10 false GND 5.552,1.563 5.906,1.729 0.354,0.167 10 false ACC 5.313,0.719 5.448,0.885 0.135,0.167 10 false 4 5.313,2.188 5.448,2.354 0.135,0.167 10 false 7 5.313,1.448 5.427,1.615 0.115,0.167 10 false 3 2.823,1.729 3.177,1.906 0.354,0.177 10 false ACC 2.833,0.979 3.156,1.156 0.323,0.177 10 false RAD 0.781,0.813 1.615,0.99 0.833,0.177 10 false from Battery 0.781,1.49 1.594,1.823 0.813,0.333 10 false from Ignition Switch 5.24,2.927 5.667,3.094 0.427,0.167 10 false G105

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
E178447
1.469,0.448 1.948,0.74 0.479,0.292 1.99,1.063 2.333,0.688 true 2.135,1.167 2.5,1.563 true 1.615,1.385 1.396,1.75 true 1.542,0.521 2.156,0.719 0.615,0.198 10 false G105 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a 2.396,0.583 2.76,0.802 0.365,0.219 10 false ACC 1.073,1.688 1.438,1.906 0.365,0.219 10 false GND 2.573,1.531 2.938,1.75 0.365,0.219 10 false B
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


Disconnect the G105 navigation receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G105-7 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G105-4 (B) - Body ground Always 11 to 14 V
G105-3 (ACC) - Body ground Ignition switch ACC 11 to 14 V
G105-3 (ACC) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR