This DTC is stored if the navigation receiver assembly judges as a result of its self check that the signals or signal lines between the navigation receiver assembly and the rear television camera assembly are not normal.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1622 | Open or Short Circuit in Back Camera Signal | Open or Short Circuit in rear television camera signal | ·
Harness or connector ·
Rear television camera assembly ·
Navigation receiver assembly |
Check for DTCs.
| Result | Proceed to |
|---|---|
| No DTC is output | A |
| DTC is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Disconnect the G153 navigation receiver assembly connector.
Disconnect the M2 rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G153-7 (CA+) - M2-4 (CB+) | Always | Below 1 Ω |
| G153-8 (V+) - M2-2 (CV+) | Always | Below 1 Ω |
| G153-15 (CGND) - M2-3 (CGND) | Always | Below 1 Ω |
| G153-16 (V-) - M2-1 (CV-) | Always | Below 1 Ω |
| G153-7 (CA+) - Body ground | Always | 10 kΩ or higher |
| G153-8 (V+) - Body ground | Always | 10 kΩ or higher |
| G153-15 (CGND) - Body ground | Always | 10 kΩ or higher |
| G153-16 (V-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Navigation Receiver Assembly) |
Disconnect the G153 navigation receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G153-15 (CGND) - Body ground | Always | Below 1 Ω |
| G153-16 (V-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Rear Television Camera Assembly) |
Disconnect the M2 rear television camera assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M2-4 (CB+) - M4-3 (CGND) | Ignition switch ON, shift lever in R | 5.5 to 7.05 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using an oscilloscope, check the waveform
| *a | Component with harness connected
(Navigation Receiver Assembly) |
*b | Waveform 1 |
| *c | Waveform 2 | *d | Synchronized Signal |
| *e | Video Waveform | - | - |
| Item | Content |
|---|---|
| Tester Connection | G153-8(V+) - G153-16 (V-) |
| Tool Setting | 0.2 V/DIV., 50 μs/DIV. |
| Condition | Waveform 1: Ignition switch ON, shift lever in R
Waveform 2: Ignition switch ON, shift lever in R, screen blacked out by covering camera lens |
Waveform is as shown in illustration.
The video waveform changes according to the image sent by the rear television camera assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Replace the rear television camera assembly with a new or normally functioning one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| No DTC is output | A |
| DTC is output | B |
A
B