Home › Power Source / Network › 2KD-FTV BATTERY / CHARGING › GENERATOR(for BOSCH Made)
RM1840EF _57 Power Source / Network _009634 2KD-FTV BATTERY / CHARGING _0052667 GENERATOR(for BOSCH Made) A

2KD-FTV BATTERY / CHARGING  GENERATOR(for BOSCH Made)  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE GENERATOR PULLEY CAP

a.

Using a screwdriver, remove the generator pulley cap from the generator pulley with clutch.


Hide 2.LOOSEN GENERATOR PULLEY WITH CLUTCH

a.

Mount the generator assembly in a vise between aluminum plates.

NOTICE:

Do not damage the generator.



b.
A200681
1.125,0.385 1.635,0.385 false 0.583,1.542 1.604,1.542 false 0.906,0.313 1.104,0.521 0.198,0.208 10 false *1 0.25,1.458 0.552,1.635 0.302,0.177 10 false SST
*1 8 mm Bi-hexagon Wrench


Set SST and an 8 mm bi-hexagon wrench to the pulley as shown in the illustration.

SST
09820-30010  


c.
A200682
1.615,1.333 1.156,1.823 1.156,1.823 0.802,1.823 true 0.906,0.583 1.104,0.583 1.104,0.583 1.656,1.021 false 2.781,0.802 2.677,0.802 2.677,0.802 2.469,1.01 false 2.833,0.688 3.052,0.854 0.219,0.167 10 false *a 0.427,1.729 0.74,1.885 0.313,0.156 10 true SST 0.719,0.49 0.896,0.667 0.177,0.177 10 false *1
*1 8 mm Bi-hexagon Wrench
*a Hold
V100135

Turn


Hold SST in place, rotate the 8 mm bi-hexagon wrench clockwise, and loosen the generator pulley with clutch.


Hide 3.REMOVE GENERATOR REAR END COVER

a.
A117269

Remove the 2 terminal covers by turning them counterclockwise.


b.
A117270

Using a 15 mm socket wrench, remove the 2 nuts from the end cover.


c.

Remove the screw and end cover.


Hide 4.REMOVE VOLTAGE REGULATOR ASSEMBLY WITH BRUSH

a.

Remove the protective tower.


b.
A117271

Remove the 3 screws and regulator.


Hide 5.REMOVE GENERATOR STATOR SUB-ASSEMBLY WITH RECTIFIER

a.
A117272

Remove the 4 screws.


b.
A117273

Using a screwdriver, pry off the stator.


Hide 6.REMOVE FITTING RING

A117274

Hide 7.REMOVE GENERATOR ROTOR ASSEMBLY

NOTICE:

Do not drop the generator rotor assembly.


a.

Remove the generator pulley with clutch.


b.
A117276

Using a press, press out the generator rotor and remove the spacer ring.


Hide 8.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A225502
1.74,0.896 1.677,0.969 false
V100135

Free


Check that the bearing is not rough or worn, and that it rotates smoothly.

If necessary, replace the drive end frame bearing.


b.
A222321

Remove the 4 screws and retainer plate.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)

i.
A222322
1.708,0.99 2.021,0.99 true 2.104,0.906 2.563,1.104 0.458,0.198 10 false SST

Using SST and a hammer, tap out the bearing.