Home › Power Source / Network › 1KD-FTV BATTERY / CHARGING › GENERATOR(for DENSO Made)
RM1840EF _57 Power Source / Network _009635 1KD-FTV BATTERY / CHARGING _0052669 GENERATOR(for DENSO Made) A

1KD-FTV BATTERY / CHARGING  GENERATOR(for DENSO Made)  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE GENERATOR WITH CLUTCH PULLEY

a.

Remove the generator pulley cap.


b.

Mount the generator in a vise between aluminum plates.


c.
A203706
1.135,2.177 0.719,2.177 false 1.333,2.698 1.552,2.698 1.552,2.698 2.052,2.25 true 0.188,2.094 0.729,2.292 0.542,0.198 10 false SST (A) 0.813,2.615 1.375,2.813 0.563,0.198 10 false SST (B)

Install SST (A) and (B) to the pulley as shown in the illustration.

SST
09820-63021  

NOTICE:

Securely attach SST to the generator pulley and generator rotor shaft.



d.
A203707
0.698,1.031 0.906,1.031 false 0.677,0.292 0.76,0.292 0.76,0.292 1.375,0.688 false 0.188,0.958 0.719,1.156 0.531,0.198 10 false SST (A) 0.156,0.219 0.688,0.417 0.531,0.198 10 false SST (B) 1.406,1.625 1.583,1.802 0.177,0.177 10 false *a
*a Hold
V100135

Turn


Use a wrench to hold SST (A) and turn SST (B) counterclockwise to loosen the generator with clutch pulley.

NOTICE:

Be careful as the generator pulley or generator rotor shaft may be damaged if the position of SST is not securely maintained while performing this operation.



e.

Remove SST from the generator.


f.

Remove the pulley.


Hide 2.REMOVE GENERATOR REAR END COVER

a.
A079302

Remove the 3 nuts and generator rear end cover.


Hide 3.REMOVE TERMINAL INSULATOR

a.
A303299

Remove the terminal insulator.


Hide 4.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A079303

Remove the 2 screws and generator brush holder assembly.


Hide 5.REMOVE GENERATOR COIL ASSEMBLY

a.
A079304

Remove the 4 through bolts.


b.
A303123
0.594,0.229 0.802,0.229 0.802,0.229 1.042,0.833 false 0.302,0.729 0.615,0.885 0.313,0.156 10 false *a 0.271,0.135 0.677,0.333 0.406,0.198 10 false SST
*a Hold
V100135

Turn


Using SST, remove the generator coil.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)


c.

Remove the generator washer.


Hide 6.REMOVE GENERATOR ROTOR ASSEMBLY

a.

Remove the generator rotor from the drive end frame.


Hide 7.CHECK GENERATOR DRIVE END FRAME BEARING

a.
A079307

Check that the bearing is not rough or worn.

If necessary, replace the generator drive end frame bearing.


Hide 8.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A079311

Remove the 4 screws and bearing retainer.


b.
A115881
1.177,1.083 0.563,1.083 0.563,1.083 1.115,1.333 true 0.208,1 0.51,1.146 0.302,0.146 10 false SST

Using SST, tap out the bearing.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)