Home › Power Source / Network › 1KD-FTV BATTERY / CHARGING › GENERATOR(for DENSO Made)
RM1840EF _57 Power Source / Network _009635 1KD-FTV BATTERY / CHARGING _0052669 GENERATOR(for DENSO Made) A

1KD-FTV BATTERY / CHARGING  GENERATOR(for DENSO Made)  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL GENERATOR DRIVE END FRAME BEARING

a.
A102672
1.813,0.969 2.5,0.281 2.5,0.281 1.865,1.198 true 2.5,0.281 2.781,0.281 false 2.854,0.198 3.25,0.375 0.396,0.177 10 false SST

Using SST and a press, press in a new bearing.

SST
09950-60010  (09951-00520)
09950-70010  (09951-07100)


b.
A079311
0.604,0.802 0.698,0.802 0.698,0.802 1.5,1.156 true 2.729,1.635 2.656,1.635 2.656,1.635 2,1.385 true 0.396,0.719 0.583,0.854 0.188,0.135 10 false *1 2.802,1.542 2.99,1.677 0.188,0.135 10 false *1
*1 Claw


Align the claws of the bearing retainer with the grooves inside the generator drive end frame.


c.

Install the bearing retainer with the 4 screws.

Torque:
2.3 N*m (23 kgf*cm, 20 in.*lbf)


Hide 2.INSTALL GENERATOR ROTOR ASSEMBLY

a.

Install the rotor and washer to the drive end frame.


Hide 3.INSTALL GENERATOR COIL ASSEMBLY

a.
A158387
1.542,0.656 2.052,0.281 2.052,0.281 2.198,0.281 true 2.313,0.188 2.5,0.354 0.188,0.167 10 false *1
*1 21 mm Deep Socket Wrench


Using a deep 21 mm socket wrench and press, slowly press on the generator coil.


b.

Install the generator coil with the 4 through bolts.

Torque:
5.9 N*m (60 kgf*cm, 52 in.*lbf)


Hide 4.INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

a.
A113845
0.99,0.531 1.219,0.344 1.219,0.344 1.313,0.344 false 1.375,0.25 1.604,0.396 0.229,0.146 10 false *1
*1 Pin


While pushing the 2 brushes into the generator brush holder, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the brush holder hole.


b.
A079303
1.354,1.646 1.479,1.646 1.479,1.646 1.667,1.292 true 1.115,1.573 1.344,1.719 0.229,0.146 10 true *1
*1 Pin


Install the brush holder with the 2 screws.

Torque:
1.8 N*m (18 kgf*cm, 16 in.*lbf)


c.

Pull out the pin from the brush holder.


Hide 5.INSTALL TERMINAL INSULATOR

Hide 6.INSTALL GENERATOR REAR END COVER

a.

Install the generator rear end cover with the 3 nuts.

Torque:
4.6 N*m (46 kgf*cm, 40 in.*lbf)


Hide 7.INSTALL GENERATOR WITH CLUTCH PULLEY

a.

Install the pulley by hand.


b.

Mount generator in a vise between aluminum plates.


c.
A203706
1.146,2.156 0.729,2.156 false 1.292,2.719 1.615,2.719 1.615,2.719 2.115,2.271 true 0.188,2.073 0.729,2.271 0.542,0.198 10 false SST (A) 0.74,2.625 1.302,2.823 0.563,0.198 10 false SST (B)

Install SST (A) and (B) to the generator with clutch pulley as shown in the illustration.

SST
09820-63021  

NOTICE:

Securely attach SST to the generator with clutch pulley and generator rotor shaft.



d.
A303128
1.281,1.281 1.281,0.719 1.281,0.719 1.135,0.719 false 0.99,1.448 0.99,1.167 0.99,1.167 0.875,1.167 false 0.594,0.625 1.094,0.823 0.5,0.198 10 false SST (B) 0.333,1.063 0.833,1.26 0.5,0.198 10 false SST (A) 1.094,2.573 1.292,2.76 0.198,0.188 10 false *a 1.708,2.573 1.948,2.771 0.24,0.198 10 false *1
*1 Fulcrum Length
*a Hold
V100135

Turn


Use a wrench to hold SST (A) and turn SST (B) clockwise to tighten the generator with clutch pulley.

Torque:
without SST : 111 N*m (1127 kgf*cm, 81 ft.*lbf)
with SST : 83 N*m (844 kgf*cm, 61 ft.*lbf)

NOTICE:

Be careful as the generator with clutch pulley or generator rotor shaft may be damaged if the position of SST is not securely maintained while performing this operation.


HINT:
·

Use a torque wrench with a fulcrum length of 300 mm (11.8 in.). When using a torque wrench with a fulcrum length that is not 300 mm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Make sure SST and the wrench are connected in a straight line.




e.

Remove SST from the generator.


f.

Check that the generator pulley rotates smoothly.


g.

Install a new generator pulley cap.