Home › Power Source / Network › 2TR-FBE BATTERY / CHARGING › GENERATOR
RM1840EF _57 Power Source / Network _009637 2TR-FBE BATTERY / CHARGING _0052674 GENERATOR A

2TR-FBE BATTERY / CHARGING  GENERATOR  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL GENERATOR DRIVE END FRAME BEARING

a.
A118448
1.167,0.927 0.5,0.292 0.5,0.292 1.031,1.198 true 0.24,0.125 0.563,0.302 0.323,0.177 10 false SST

Using SST and a press, press in a new bearing.

SST
09950-60010  (09951-00470)
09950-70010  (09951-07100)


b.
A118449
1.5,1.438 1.135,1.833 1.135,1.833 1.031,1.833 true 1.729,0.885 2.208,0.26 2.208,0.26 2.323,0.26 true 0.823,1.75 1.021,1.917 0.198,0.167 10 false *1 2.375,0.177 2.573,0.344 0.198,0.167 10 false *1
*1 Claw


Align the claws of the bearing retainer with the grooves inside the drive end frame.


c.

Install the bearing retainer with the 4 screws.

Torque:
2.3 N*m (23 kgf*cm, 20 in.*lbf)


Hide 2.INSTALL GENERATOR ROTOR ASSEMBLY

a.

Install the generator rotor to the drive end frame.

NOTICE:

Do not drop the generator rotor.



b.

Install the generator drive end frame space collar to the generator rotor.


c.

Install the washer to the generator rotor.


Hide 3.INSTALL GENERATOR COIL ASSEMBLY

a.
A118450
1.823,0.604 2.073,0.24 2.073,0.24 2.219,0.24 false 2.271,0.146 2.5,0.344 0.229,0.198 10 false *1
*1 Deep Socket Wrench (21 mm)


Using a 21 mm deep socket wrench and press, slowly press in the generator coil assembly.


b.

Install the generator coil assembly with the 4 through bolts.

Torque:
5.9 N*m (60 kgf*cm, 52 in.*lbf)


Hide 4.INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

a.
A118452
0.99,0.854 1.25,0.542 1.25,0.542 1.438,0.542 true 1.49,0.469 1.719,0.615 0.229,0.146 10 false *1
*1 Pin


While pushing the 2 brushes into the generator brush holder, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the brush holder hole.


b.
A118453
1.719,0.854 1.615,1.094 1.615,1.094 1.615,1.198 true 1.573,1.229 1.76,1.385 0.188,0.156 10 false *1
*1 Pin


Install the brush holder with the 2 screws.

Torque:
1.8 N*m (18 kgf*cm, 16 in.*lbf)


c.

Pull out the pin from the brush holder.


Hide 5.INSTALL TERMINAL INSULATOR

a.
A118454

Install the terminal insulator.

NOTICE:

Make sure the terminal insulator is installed facing the proper direction.



Hide 6.INSTALL GENERATOR REAR END COVER

a.

Install the generator rear end cover with the 3 nuts.

Torque:
4.6 N*m (46 kgf*cm, 40 in.*lbf)


Hide 7.INSTALL GENERATOR PULLEY

a.

Mount the generator in a vise between aluminum plates.


b.

Install the pulley to the rotor shaft by tightening the generator pulley nut by hand.


c.
A246527
3.177,0.521 2.76,0.177 2.76,0.177 2.354,0.177 true 3.01,0.771 3.01,1.24 true 1.417,1.979 1.583,2.135 0.167,0.156 10 true *a 1.781,0.094 2.344,0.25 0.563,0.156 10 false SST 1-A 2.729,1.292 3.292,1.448 0.563,0.156 10 false SST 1-B 0.49,1.698 0.656,1.854 0.167,0.156 10 true *b
*a Hold
*b Turn


Install SST 1-A and 1-B to the rotor shaft.

SST
09820-63011  (09820-06010, 09820-06021)

Item Part No.
SST 1-A and 1-B 09820-06010
SST 2 09820-06021


d.

Hold SST 1-A with a torque wrench, and turn SST 1-B clockwise with the specified torque.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)

NOTICE:

Make sure that the SST is secured to the rotor shaft.



e.
A203850
2.708,0.5 2.781,0.5 2.781,0.5 2.833,0.771 false 2.271,0.438 2.688,0.583 0.417,0.146 10 false SST 2
V100135

Insert


Insert SST 2 to attach it to the pulley nut.


f.
A246523
0.58,1.424 0.738,1.581 0.158,0.156 10 *b 0.99,1.823 1.16,1.979 0.17,0.156 10 *a
*a Turn
*b Hold


Tighten the pulley nut by turning SST 1-A in the direction shown in the illustration.

Torque:
111 N*m (1127 kgf*cm, 81 ft.*lbf)


g.

Remove SST 2 from the generator.


h.
A246528
3.177,0.5 2.781,0.156 2.781,0.156 2.365,0.156 true 3,0.76 3,1.167 true 0.521,1.479 0.688,1.625 0.167,0.146 10 false *a 1.813,0.073 2.375,0.229 0.563,0.156 10 false SST 1-A 2.74,1.188 3.302,1.344 0.563,0.156 10 false SST 1-B 1.323,1.927 1.49,2.083 0.167,0.156 10 true *b
*a Turn
*b Hold


Turn SST 1-B in the direction shown in the illustration and remove SST 1-A and 1-B.


i.

Turn the pulley and check that the pulley moves smoothly.