Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(w/ VSC) › 2011.10–2012.01
RM1840EF _57 Power Source / Network _009639 NETWORKING _0052677 CAN COMMUNICATION SYSTEM(w/ VSC) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ VSC)  Steering Angle Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Steering Angle Sensor Communication Stop Mode Either condition is met:
·

"Spiral cable (Steering Angle Sensor)" is not displayed on the "Bus Check" screen.

·

"Steering Angle Sensor Communication Stop Mode" in "DTC Communication Table" applies.


·

Power source or inside of spiral cable sub-assembly (steering angle sensor)

·

Spiral cable sub-assembly (steering angle sensor) CAN branch wire or connector

·

Spiral cable sub-assembly (steering angle sensor)



WIRING DIAGRAM

C240994
5.375,3.948 5.656,4.115 0.281,0.167 10 false G83 5.375,4.094 7.073,4.469 1.698,0.375 10 false Spiral Cable Sub-assembly (Steering Angle Sensor) 5.75,1.094 6.167,1.271 0.417,0.177 10 false CANL 5.75,0.563 6.156,0.75 0.406,0.188 10 false CANH 5.563,0.469 5.677,0.625 0.115,0.156 10 false 4 5.563,0.99 5.719,1.135 0.156,0.146 10 false 3 5.75,3.156 6.177,3.333 0.427,0.177 10 false ESS 5.771,2.635 6.177,2.823 0.406,0.188 10 false IG 5.76,2.125 6.156,2.281 0.396,0.156 10 false BAT 5.563,2.01 5.677,2.167 0.115,0.156 10 false 6 5.552,2.521 5.656,2.677 0.104,0.156 10 false 5 5.552,3.031 5.656,3.188 0.104,0.156 10 false 2 1.604,0.469 1.76,0.635 0.156,0.167 10 false 2 1.615,0.979 1.844,1.125 0.229,0.146 10 false 1 0.5,1.385 0.833,1.531 0.333,0.146 10 false G85 0.51,1.552 2.115,1.75 1.604,0.198 10 false No. 3 Junction Connector 1.708,2.083 2.49,2.281 0.781,0.198 10 false from Battery 1.25,2.604 2.5,2.802 1.25,0.198 10 false from Ignition Switch 3.5,2.469 4.583,2.635 1.083,0.167 10 false ECU-IG&GAUGE 3.823,1.958 4.302,2.135 0.479,0.177 10 false ECU-B

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Result:
Proceed to
NEXT



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (STEERING ANGLE SENSOR CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (STEERING ANGLE SENSOR CAN BRANCH WIRE)
a.

Disconnect the G83 spiral cable sub-assembly (steering angle sensor) connector.


C234977
0.438,1 1.042,1.344 0.604,0.344 1.771,1.313 2.135,1.792 2.135,1.792 2.25,1.792 true 1.667,1.313 1.323,1.781 1.323,1.781 1.219,1.781 true 0.615,1.094 0.917,1.25 0.302,0.156 10 false G83 0.823,1.708 1.25,1.875 0.427,0.167 10 false CANH 2.281,1.729 2.677,1.906 0.396,0.177 10 false CANL 0.073,0.042 0.375,0.208 0.302,0.167 10 false *a
*a Rear view of wire harness connector
(to Spiral Cable Sub-assembly [Steering Angle Sensor])


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G83-4 (CANH) - G83-3 (CANL) Ignition switch off 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (STEERING ANGLE SENSOR - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE STEERING ANGLE SENSOR CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (STEERING ANGLE SENSOR - BATTERY AND BODY GROUND)
a.
C234977
2.385,0.99 2.99,1.333 0.604,0.344 1.927,1.323 2.198,1.781 2.198,1.781 2.302,1.781 true 1.417,1.177 1.25,0.948 1.25,0.948 1.146,0.948 true 1.552,1.323 1.292,1.729 1.292,1.729 1.188,1.729 true 2.552,1.073 2.885,1.219 0.333,0.146 10 false G83 0.865,0.875 1.177,1.021 0.313,0.146 10 false BAT 1.021,1.646 1.24,1.813 0.219,0.167 10 false IG 2.333,1.708 2.656,1.854 0.323,0.146 10 false ESS 0.073,0.031 0.375,0.198 0.302,0.167 10 false *a
*a Rear view of wire harness connector
(to Spiral Cable Sub-assembly [Steering Angle Sensor])


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G83-6 (BAT) - Body ground Always 11 to 14 V
G83-5 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G83-2 (ESS) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR