Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(w/ VSC) › 2011.10–2012.01
RM1840EF _57 Power Source / Network _009639 NETWORKING _0052677 CAN COMMUNICATION SYSTEM(w/ VSC) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ VSC)  Yaw Rate Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Yaw Rate Sensor Communication Stop Mode Either condition is met:
·

"Yaw Rate Sensor" is not displayed on the "Bus Check" screen.

·

"Yaw Rate Sensor Communication Stop Mode" in "DTC Communication Table" applies.


·

Power source or inside of yaw rate sensor assembly

·

Yaw rate sensor assembly CAN branch wire or connector

·

Yaw rate sensor assembly



WIRING DIAGRAM

C240995
5.594,3.781 5.885,3.938 0.292,0.156 10 false K21 5.604,3.927 6.719,4.313 1.115,0.385 10 false Yaw Rate Sensor Assembly 5.75,1.427 6.229,1.604 0.479,0.177 10 false CANL 5.75,0.917 6.26,1.135 0.51,0.219 10 false CANH 5.542,0.823 5.677,0.969 0.135,0.146 10 false 3 5.542,1.333 5.667,1.479 0.125,0.146 10 false 2 5.74,3.115 6.156,3.292 0.417,0.177 10 false GND 5.76,2.448 6.146,2.635 0.385,0.188 10 false IG 5.552,2.354 5.656,2.51 0.104,0.156 10 false 4 5.552,3.021 5.656,3.156 0.104,0.135 10 false 1 1.615,0.823 1.792,0.958 0.177,0.135 10 false 7 1.615,1.333 1.781,1.49 0.167,0.156 10 false 18 0.51,1.719 0.875,1.865 0.365,0.146 10 false G86 0.51,1.875 2.115,2.063 1.604,0.188 10 false No. 2 Junction Connector 1.25,2.448 2.5,2.646 1.25,0.198 10 false from Ignition Switch 3.479,2.313 4.583,2.5 1.104,0.188 10 false ECU-IG&GAUGE

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Result:
Proceed to
NEXT



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (YAW RATE SENSOR ASSEMBLY CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (YAW RATE SENSOR ASSEMBLY CAN BRANCH WIRE)
a.
C222816
1.458,0.354 2.031,0.677 0.573,0.323 1.625,1.406 1.823,1.896 1.823,1.896 1.948,1.896 true 1.479,1.406 1.302,1.885 1.302,1.885 1.177,1.885 true 0.115,0.115 0.333,0.302 0.219,0.188 10 false *a 1.625,0.438 1.927,0.604 0.302,0.167 10 false K21 1.99,1.823 2.406,2 0.417,0.177 10 false CANH 0.792,1.813 1.188,1.969 0.396,0.156 10 false CANL
*a Front view of wire harness connector
(to Yaw Rate Sensor Assembly)


Disconnect the K21 yaw rate sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
K21-3 (CANH) - K21-2 (CANL) Ignition switch off 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (YAW RATE SENSOR ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE YAW RATE SENSOR ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (YAW RATE SENSOR ASSEMBLY - BATTERY AND BODY GROUND)
a.
C222816
1.458,0.354 2.031,0.677 0.573,0.323 1.792,1.406 2,1.906 2,1.906 2.125,1.906 true 1.302,1.396 1.135,1.906 1.135,1.906 1.01,1.906 true 1.625,0.438 1.917,0.615 0.292,0.177 10 false K21 0.115,0.115 0.333,0.302 0.219,0.188 10 false *a 2.156,1.823 2.542,2 0.385,0.177 10 false IG 0.698,1.823 1.031,1.99 0.333,0.167 10 false GND
*a Front view of wire harness connector
(to Yaw Rate Sensor Assembly)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K21-4 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K21-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR