Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(w/ VSC) › 2011.10–2012.04
RM1840EF _57 Power Source / Network _009639 NETWORKING _0052677 CAN COMMUNICATION SYSTEM(w/ VSC) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ VSC)  ECM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
ECM Communication Stop Mode Either condition is met:
·

"ECM (Engine)" is not displayed on the "Bus Check" screen.

·

"ECM Communication Stop Mode" in "DTC Communication Table" applies.


·

Power source or inside of ECM

·

ECM



WIRING DIAGRAM

C236846
5.958,4.469 6.385,4.677 0.427,0.208 10 false ECM 5.76,3.281 6.125,3.448 0.365,0.167 10 false E01 5.771,2.771 6.167,2.938 0.396,0.167 10 false E1 5.75,3.802 6.115,4.021 0.365,0.219 10 false E02 5.771,1.781 6.271,2.052 0.5,0.271 10 false MREL 5.771,2.281 6.25,2.49 0.479,0.208 10 false IGSW 5.375,2.25 5.688,2.458 0.313,0.208 10 false G39 5.469,2.042 5.719,2.479 0.25,0.438 10 false 9 5.375,1.74 5.667,1.927 0.292,0.188 10 false G39 5.479,1.531 5.677,1.802 0.198,0.271 10 false 8 5.375,1.229 5.677,1.406 0.302,0.177 10 false G39 5.458,1.031 5.625,1.26 0.167,0.229 10 false 1 5.375,3.802 5.677,4.031 0.302,0.229 10 false C22 5.469,3.594 5.635,3.771 0.167,0.177 10 false 6 5.385,3.281 5.677,3.469 0.292,0.188 10 false C22 5.479,3.083 5.688,3.281 0.208,0.198 10 false 7 5.385,2.771 5.667,2.927 0.281,0.156 10 false C23 5.479,2.573 5.74,2.844 0.26,0.271 10 false 7 5.375,0.708 5.771,0.938 0.396,0.229 10 false G38 5.479,0.51 5.635,0.708 0.156,0.198 10 false 2 5.76,1.24 5.958,1.427 0.198,0.188 10 false +B 5.76,0.719 6.188,0.917 0.427,0.198 10 false BATT 1.427,1.208 2.521,1.5 1.094,0.292 10 false from MAIN Relay 1.688,0.708 2.521,0.958 0.833,0.25 10 false from Battery 3.938,0.573 4.25,0.823 0.313,0.25 10 false EFI 3.917,2.115 4.26,2.365 0.344,0.25 10 false IGN 1.563,1.719 2.552,2.042 0.99,0.323 10 false to MAIN Relay 1.24,2.24 2.594,2.531 1.354,0.292 10 false from Ignition Switch

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)
a.

Disconnect the C22, C23, G38 and G39 ECM connectors.

C236880
0.865,0.667 1.313,0.917 0.448,0.25 2.438,0.667 2.885,0.917 0.448,0.25 4.344,0.667 4.792,0.917 0.448,0.25 6.094,0.667 6.542,0.917 0.448,0.25 0.677,1.646 0.938,2.167 0.938,2.167 1.031,2.167 true 0.552,2.323 0.427,2.323 0.427,2.323 0.573,1.646 true 0.563,0.917 0.677,0.917 0.677,0.917 0.604,1.375 true 2.198,0.917 2.302,0.917 2.302,0.917 2.448,1.385 true 5.302,1.063 5.198,1.063 5.198,1.063 5.115,1.385 true 6.781,0.927 6.667,0.927 6.667,0.927 6.781,1.375 true 6.625,1.479 6.792,2.219 6.792,2.219 6.708,2.219 true 0.969,0.719 1.25,0.865 0.281,0.146 10 false G39 2.552,0.719 2.865,0.906 0.313,0.188 10 false G38 4.448,0.719 4.729,0.875 0.281,0.156 10 false C23 6.208,0.719 6.479,0.896 0.271,0.177 10 false C22 0.063,0.052 0.344,0.323 0.281,0.271 10 false *a 0.375,0.823 0.573,0.969 0.198,0.146 10 false +B 1.854,0.844 2.229,0.99 0.375,0.146 10 false BATT 5.323,0.99 5.51,1.135 0.188,0.146 10 false E1 6.802,0.854 7.073,1 0.271,0.146 10 false E01 0.573,2.24 1,2.385 0.427,0.146 10 false MREL 1.063,2.094 1.49,2.24 0.427,0.146 10 false IGSW 6.438,2.135 6.708,2.281 0.271,0.146 10 false E02
*a Front view of wire harness connector
(to ECM)
- -



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G38-2 (BATT) - Body ground Always 11 to 14 V
G39-1 (+B) - Body ground Battery positive (+) voltage applied to terminal G39-8 (MREL) 11 to 14 V
G39-9 (IGSW) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C23-7 (E1) - Body ground Always Below 1 Ω
C22-7 (E01) - Body ground Always Below 1 Ω
C22-6 (E02) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR