Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(for Built-in Type Door Control Receiver)
RM1840EF _58 Vehicle Interior _009640 DOOR LOCK _0052678 WIRELESS DOOR LOCK CONTROL SYSTEM(for Built-in Type Door Control Receiver) M

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(for Built-in Type Door Control Receiver)  REGISTRATION  


PROCEDURE

Hide 1. DESCRIPTION OF CODE REGISTRATION

HINT:
·

Recognition code registration is necessary when replacing the door control transmitter assembly or the theft warning ECU assembly.

·

Add mode is used to register new recognition codes while retaining codes already registered. This mode is used when a new door control transmitter assembly is added. If the number of registered codes exceeds 4, the previously registered codes will be erased in order, starting from the first registered code.

·

Rewrite mode is used to erase all previously registered recognition codes in order to register new recognition codes. This mode is used when the door control transmitter assembly or the theft warning ECU assembly is replaced.

·

Synchronization mode is used to renew the sequential code (rolling code) of the door control transmitter assembly and synchronize it with the registered recognition code. This mode is used when the door control transmitter assembly does not function because they are unsynchronized. Up to 4 door control transmitter assemblies can be synchronized at once (If a door control transmitter assembly's switch is pressed while out of range of the theft warning ECU assembly, the system will not be able to synchronize the sequential code (rolling code) with the registered recognition code. At this time, the system will automatically synchronize them. However, automatic synchronization can be performed only 500 times. Therefore, it its necessary to use this mode after they have synchronized 500 times).

·

Erase mode is used to erase all the registered codes and disable the wireless door lock function. This mode is used when the door control transmitter assembly is lost.

·

All of the following registration procedures must be performed in order.



Hide 2. REGISTER RECOGNITION CODE

a.

Check that the following condition is met.

No key in the ignition key cylinder.


b.

Insert the key into the ignition key cylinder.


c.

Wait for the 5 seconds.

HINT:

If the key is pulled out from the ignition key cylinder or the ignition switch is turned to ON, the registration mode will be canceled.



d.

Turn the ignition switch from off to ON 5 times within 10 seconds to turn on the security indicator light assembly.

HINT:

If the key is pulled out from the ignition key cylinder, the registration mode will be canceled.



e.

Open and close the driver side door once and turn the ignition switch from ON to off within 30 seconds.

HINT:

If the key is pulled out from the ignition key cylinder or the driver side door is opened and closed twice or more, the registration mode will be canceled.



f.
B276318
0.198,0.125 2.573,0.302 2.375,0.177 10 false Security Horn Assembly Output: Once 0.208,1.771 2.5,1.948 2.292,0.177 10 false Hazard Warning Lights Output: Once 0.365,0.885 0.573,1.063 0.208,0.177 10 false On 1.51,0.76 2.042,0.938 0.531,0.177 10 false 0.2 sec. 1.74,2.417 2.333,2.594 0.594,0.177 10 false 0.35 sec. 0.365,1.25 0.573,1.427 0.208,0.177 10 false Off 0.375,2.521 0.583,2.698 0.208,0.177 10 false On 0.365,2.906 0.573,3.083 0.208,0.177 10 false Off

Check the response to registration mode.


g.

Perform the following operations (mode selection) within 30 seconds.

i.

Perform the driver side door open-close operation according to details below. Then turn the ignition switch ON and off.

Number of open-close operations of the driver side door:

·

Add mode

Open-close operation: Once

·

Rewrite mode:

Open-close operation: Twice

·

Synchronization mode:

Open-close operation: 3 times

·

Erase mode:

Open-close operation: 4 times


HINT:

If any of the following operations are performed, the registration mode will be canceled.

·

The key is removed from the ignition key cylinder.

·

The driver side door is opened and closed 5 times or more.

·

The ignition switch is turned ON before opening the driver side door.





h.

Check the response to the selected mode.

B123988
0.375,1.135 1.115,1.323 0.74,0.188 10 false Add Mode 1.948,1.115 6.521,1.354 4.573,0.24 10 false Security horn assembly sounds and hazard warning lights flash: Once 0.167,0.083 6.948,0.302 6.781,0.219 10 false Response to selected mode (security horn assembly and hazard warning lights outputs) 0.167,0.396 6.948,0.781 6.781,0.385 10 false Theft warning ECU assembly automatically sounds security horn assembly and flashes hazard warning lights to inform which mode has been selected. 0.75,1.51 3.229,1.708 2.479,0.198 10 false Security Horn Assembly Operation 4.188,1.469 6.781,1.698 2.594,0.229 10 false Hazard Warning Lights Operation 1.031,1.74 1.25,1.948 0.219,0.208 10 false T1 4.563,1.729 4.781,1.938 0.219,0.208 10 false T2 0.302,2.063 0.521,2.229 0.219,0.167 10 false On 0.302,2.365 0.531,2.542 0.229,0.177 10 false Off 3.75,2.063 3.969,2.229 0.219,0.167 10 false On 3.75,2.365 3.979,2.542 0.229,0.177 10 false Off 0.302,3.719 0.521,3.885 0.219,0.167 10 false On 0.302,4.031 0.531,4.208 0.229,0.177 10 false Off 3.74,3.719 3.958,3.885 0.219,0.167 10 false On 3.74,4.031 3.969,4.208 0.229,0.177 10 false Off 0.302,5.375 0.521,5.542 0.219,0.167 10 false On 0.302,5.688 0.531,5.865 0.229,0.177 10 false Off 0.302,7.042 0.521,7.208 0.219,0.167 10 false On 0.313,7.344 0.542,7.521 0.229,0.177 10 false Off 0.302,8.229 0.521,8.396 0.219,0.167 10 false On 0.313,8.531 0.542,8.708 0.229,0.177 10 false Off 3.74,5.375 3.958,5.542 0.219,0.167 10 false On 3.74,5.688 3.969,5.865 0.229,0.177 10 false Off 0.385,2.792 1.281,2.979 0.896,0.188 10 false Rewrite Mode 1.938,2.792 6.969,3.031 5.031,0.24 10 false Security horn assembly sounds assembly and hazard warning lights flash: Twice 0.75,3.177 3.313,3.375 2.563,0.198 10 false Security Horn Assembly Operation 4.188,3.135 6.781,3.333 2.594,0.198 10 false Hazard Warning Lights Operation 1.021,3.396 1.24,3.604 0.219,0.208 10 false T1 1.458,3.396 1.677,3.604 0.219,0.208 10 false T3 4.552,3.385 4.771,3.594 0.219,0.208 10 false T2 5.01,3.385 5.229,3.594 0.219,0.208 10 false T2 1.021,5.052 1.24,5.26 0.219,0.208 10 false T1 1.458,5.052 1.677,5.26 0.219,0.208 10 false T3 1.021,6.719 1.24,6.927 0.219,0.208 10 false T1 1.469,6.719 1.688,6.927 0.219,0.208 10 false T3 4.188,4.813 6.781,5.01 2.594,0.198 10 false Hazard Warning Lights Operation 4.552,5.052 4.771,5.26 0.219,0.208 10 false T2 5,5.052 5.219,5.26 0.219,0.208 10 false T2 0.74,7.646 3.333,7.844 2.594,0.198 10 false Hazard Warning Lights Operation 1.115,7.906 1.333,8.115 0.219,0.208 10 false T2 1.563,7.906 1.781,8.115 0.219,0.208 10 false T2 0.365,4.438 1.813,4.646 1.448,0.208 10 false Synchronization Mode 1.948,4.448 6.521,4.688 4.573,0.24 10 false Security horn assembly sounds and hazard warning lights flash: 3 times 0.75,4.823 3.177,5.021 2.427,0.198 10 false Security Horn Assembly Operation 0.375,6.104 1.76,6.292 1.385,0.188 10 false Erase Mode 1.948,6.115 6.521,6.354 4.573,0.24 10 false Security horn assembly sounds and hazard warning lights flash: 5 times 0.75,6.479 3.333,6.729 2.583,0.25 10 false Security Horn Assembly Operation 6.063,7.406 6.948,7.583 0.885,0.177 10 false T1: 0.2 sec. 6.063,7.688 6.948,7.844 0.885,0.156 10 false T2: 0.35 sec. 6.063,7.938 6.948,8.115 0.885,0.177 10 false T3: 0.5 sec.

HINT:

If erase mode is selected, the registration procedures are completed.



i.

Press the lock and unlock switches on the transmitter simultaneously.


j.

Press a single switch (lock or unlock).


k.

After completing the above step, check the response to the registration completion within 3 seconds.

B123989
0.385,0.969 3.99,1.177 3.604,0.208 10 false Lock-Unlock and Security Horn Sounds Occur Once 0.75,1.469 3.729,1.698 2.979,0.229 10 false Registration of recognition code has completed. 0.167,0.083 6.948,0.302 6.781,0.219 10 false Response to registration completion (security horn and hazard warning lights outputs) 0.167,0.396 6.99,0.667 6.823,0.271 10 false Theft warning ECU assembly automatically sounds security horn assembly and flashes hazard warning lights. 1.042,1.927 2.51,2.125 1.469,0.198 10 false Lock-Unlock Operation 4.927,2.271 7.073,2.521 2.146,0.25 10 false Hazard Warning Lights Operation 1.344,2.177 1.563,2.385 0.219,0.208 10 false T1 5.24,2.521 5.458,2.729 0.219,0.208 10 false T1 1.938,2.177 2.156,2.385 0.219,0.208 10 false T2 2.604,2.177 2.823,2.385 0.219,0.208 10 false T1 0.469,2.521 0.792,2.698 0.323,0.177 10 false Lock 0.594,2.833 0.813,3.01 0.219,0.177 10 false Off 0.344,3.135 0.792,3.313 0.448,0.177 10 false Unlock 0.469,5.542 0.813,5.802 0.344,0.26 10 false Lock 0.583,5.865 0.802,6.042 0.219,0.177 10 false Off 0.344,6.156 0.865,6.417 0.521,0.26 10 false Unlock 4.479,2.875 4.688,3.021 0.208,0.146 10 false On 4.479,3.177 4.708,3.344 0.229,0.167 10 false Off 0.385,3.99 3.688,4.208 3.302,0.219 10 false Lock-Unlock and Security Horn Sounds Occur Twice 0.75,4.5 3.427,4.719 2.677,0.219 10 false Registration of recognition code has failed. 1.042,4.958 3.219,5.156 2.177,0.198 10 false Lock-Unlock Operation 1.021,6.771 3.167,7.021 2.146,0.25 10 false Hazard Warning Lights Operation 1.344,5.208 1.563,5.417 0.219,0.208 10 false T1 1.344,7.031 1.563,7.24 0.219,0.208 10 false T1 1.938,5.208 2.156,5.417 0.219,0.208 10 false T2 2.198,7.031 2.417,7.24 0.219,0.208 10 false T3 2.604,5.208 2.823,5.417 0.219,0.208 10 false T1 0.594,7.354 0.802,7.5 0.208,0.146 10 false On 0.594,7.677 0.823,7.833 0.229,0.156 10 false Off 6.01,7.615 6.875,7.792 0.865,0.177 10 false T1: 0.25 sec. 6.01,7.885 6.854,8.063 0.844,0.177 10 false T2: 0.75 sec. 6.01,8.146 6.781,8.333 0.771,0.188 10 false T3: 1.0 sec.

HINT:
·

If lock-unlock operation and the security horn assembly sounds occur twice, the registration of the recognition code has failed. Perform the registration procedures again from the beginning.

·

If registering another transmitter, repeat the procedures after the response to the selected mode confirmation. All 4 recognition codes can be registered consecutively.




l.

Perform either of the following.

i.

Open the door.


ii.

Insert the key into the ignition key cylinder.


iii.

Turn the ignition switch to ON.



m.

Registration of the recognition codes (add mode and rewrite mode) is completed.