CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY
| *1 | Integration Relay | - | - |
Disconnect the 2D, 2H and 2L driver side junction block assembly connectors.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 2D-9 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| 2D-18 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| 2H-4 (ALTB) - Body ground | LG - Body ground | Battery power supply | Always | 11 to 14 V |
| 2L-12 (BECU) - Body ground | L - Body ground | Battery power supply | Always | 11 to 14 V |
If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the 2D, 2H and 2L driver side junction block assembly connectors.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 2A-4 (L1) - Body ground | L - Body ground | ·
Power window regulator master switch assembly (door control switch) lock input signal ·
Driver side door key-linked lock input signal |
·
Power window regulator master switch assembly (door control switch) locked ·
Driver side door key cylinder in lock position |
Below 1 V |
·
Power window regulator master switch assembly (door control switch) off ·
Ignition switch off, all doors closed and driver side door key cylinder in neutral position |
11 to 14 V | |||
| 2D-4 (UL1) - Body ground | L-W - Body ground | ·
Power window regulator master switch assembly (door control switch) unlock input signal ·
Driver side door key-linked unlock input signal |
·
Power window regulator master switch assembly (door control switch) unlocked ·
Driver side door key cylinder in unlock position |
Below 1 V |
·
Power window regulator master switch assembly (door control switch) off ·
Ignition switch off, all doors closed and driver side door key cylinder in neutral position |
11 to 14 V | |||
| 2K-10 (ACT-) - Body ground | L-Y - Body ground | Door lock motor unlock drive output signal (passenger door and rear RH door) | Power window regulator master switch assembly (door control switch) not pushed and driver side door key cylinder in neutral position | Below 1 V |
| Lock side of power window regulator master switch assembly (door control switch) pushed, or driver side door key cylinder in unlock position | 11 to 14 V | |||
| 2K-11 (ACT+) - Body ground | L - Body ground | Door lock motor lock drive output signal (passenger door and rear RH door) | Power window regulator master switch assembly (door control switch) not pushed and driver side door key cylinder in neutral position | Below 1 V |
| Lock side of power window regulator master switch assembly (door control switch) pushed, or driver side door key cylinder in lock position | 11 to 14 V | |||
| 2O-27 (DCTY) - Body ground | R-B - Body ground | Front door courtesy light switch assembly LH input signal | Driver side door open | Below 1 V |
| Driver side door closed | 11 to 14 V | |||
| 2R-27 (ACT-) - Body ground | L-Y - Body ground | Door lock motor unlock drive output signal (driver door and rear LH door) | Power window regulator master switch assembly (door control switch) not pushed and driver side door key cylinder in neutral position | Below 1 V |
| Lock side of power window regulator master switch assembly (door control switch) pushed, or driver side door key cylinder in unlock position | 11 to 14 V | |||
| 2R-28 (ACT+) - Body ground | L - Body ground | Door lock motor lock drive output signal (driver door and rear LH door) | Power window regulator master switch assembly (door control switch) not pushed and driver side door key cylinder in neutral position | Below 1 V |
| Lock side of power window regulator master switch assembly (door control switch) pushed, or driver side door key cylinder in lock position | 11 to 14 V |
If the result is not as specified, the driver side junction block assembly may have a malfunction.
CHECK THEFT WARNING ECU ASSEMBLY (w/ Theft Deterrent System)
Disconnect the G29 theft warning ECU assembly connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G29-1 (E) - Body ground | B-W - Body ground | Ground | Always | Below 1 Ω |
| G29-4 (+B1) - Body ground | L-Y - Body ground | Battery power supply | Always | 11 to 14 V |
| G29-14 (+B2) Body ground | G - Body ground | Battery power supply | Always | 11 to 14 V |
| G29-18 (IG) Body ground | R-L - Body ground | Ignition power supply | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V |
If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the G29 theft warning ECU assembly connector.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G29-7 (CTY) - Body ground | R-L - Body ground | All Door courtesy switches input signal | One or more doors open | Below 1 V |
| All doors closed | 11 to 14 V | |||
| G29-17 (SPD) - Body ground | V-R - Body ground | Vehicle speed input signal | Driving at approximately 20 km/h (12.4 mph) | Pulse generation (See waveform 1) |
If the result is not as specified, the theft warning ECU assembly may have a malfunction.
Inspect using an oscilloscope.
The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
As the vehicle speed increases, the wavelength shortens.
Waveform 1 (Reference)
| Item | Content |
|---|---|
| Tester Connection | G29-17 (SPD) - Body ground |
| Tool Setting | 5 V/DIV., 10 msec./DIV. |
| Condition | Driving at approximately 20 km/h (12.4 mph) |