Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK
RM1840EF _58 Vehicle Interior _009640 DOOR LOCK _0052686 FRONT DOOR LOCK G

DOOR LOCK  FRONT DOOR LOCK  INSPECTION  


PROCEDURE

Hide 1.INSPECT FRONT DOOR LOCK ASSEMBLY LH

B277598
4.896,1.458 4.323,1.625 true 5.656,1.458 6.167,1.625 true 2.354,2.156 2.604,2.417 0.25,0.26 10 false *a 1.875,2.469 2.146,2.688 0.271,0.219 10 false *b 4.583,0.521 4.875,0.781 0.292,0.26 10 false *c 6.188,1.563 6.5,1.771 0.313,0.208 10 false UL 4.198,1.563 4.479,1.76 0.281,0.198 10 false L
*a Lock *b Unlock
*c Component without harness connected (Front Door Lock Assembly LH) - -


a.

Check the door lock motor operation.

i.

Apply battery voltage to the motor connector and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 1 (UL)
Lock
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 4 (L)
Unlock


If the result is not as specified, replace the front door lock assembly LH.




b.

Check the door lock and unlock switch.

i.

Measure the resistance according to the value(s) in the table below.

B277599
4.906,1.667 4.552,2.042 true 5.052,1.677 4.99,2.042 true 5.375,1.646 5.688,2.031 true 5.219,1.677 5.323,2.021 true 2.75,0.833 2.958,1.042 0.208,0.208 10 false *a 2.813,1.49 3.021,1.698 0.208,0.208 10 false *b 2.385,2.021 2.594,2.229 0.208,0.208 10 false *c 5.688,2.042 5.854,2.219 0.167,0.177 10 false E 4.948,2.042 5.188,2.219 0.24,0.177 10 false L 4.479,2.042 4.75,2.219 0.271,0.177 10 false UL 5.167,2.042 5.656,2.25 0.49,0.208 10 false LSSR 4.542,0.448 4.75,0.656 0.208,0.208 10 false *d
*a Lock *b Off
*c Unlock *d Component without harness connected (Front Door Lock Assembly LH)


Standard Resistance:
Tester Connection Condition Specified Condition
9 (L) - 7 (E) Lock Below 1 Ω
9 (L) - 7 (E)
10 (UL) - 7 (E)
Off 10 kΩ or higher
10 (UL) - 7 (E) Unlock Below 1 Ω


If the result is not as specified, replace the front door lock assembly LH.



ii.

Check the detection switch.

1.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
8 (LSSR) - 7 (E) Lock 10 kΩ or higher
Unlock Below 1 Ω


If the result is not as specified, replace the front door lock assembly LH.




Hide 2.INSPECT FRONT DOOR LOCK ASSEMBLY RH

B277600
5.677,1.448 6.073,1.49 true 4.906,1.448 4.24,1.563 true 1.188,2.094 1.396,2.313 0.208,0.219 10 false *a 1.823,2.417 2.063,2.635 0.24,0.219 10 false *b 4.594,0.521 4.885,0.771 0.292,0.25 10 false *c 6.115,1.417 6.49,1.656 0.375,0.24 10 false UL 4.125,1.5 4.5,1.74 0.375,0.24 10 false L
*a Unlock *b Lock
*c Component without harness connected (Front Door Lock Assembly RH) - -


a.

Check the door lock motor operation.

i.

Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 1 (UL)
Lock
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 4 (L)
Unlock


If the result is not as specified, replace the front door lock assembly RH.