Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › 2011.10–2012.04
RM1840EF _58 Vehicle Interior _009641 THEFT DETERRENT / KEYLESS ENTRY _0052688 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Driver Side Door Courtesy Switch Circuit  


DESCRIPTION

The theft warning ECU assembly detects the condition of the front door courtesy light switch assembly LH.

WIRING DIAGRAM

B275968
5.177,1.229 5.51,1.417 0.333,0.188 10 false G29 5.771,0.573 6.104,0.76 0.333,0.188 10 false CTY 5.583,0.5 5.729,0.688 0.146,0.188 10 false 7 4.427,0.5 4.625,0.688 0.198,0.188 10 false 17 3.948,0.5 4.385,0.667 0.438,0.167 10 false DOOR 3.292,0.5 3.729,0.667 0.438,0.167 10 false DCTY 3.052,0.5 3.25,0.688 0.198,0.188 10 false 16 1.698,1.083 1.896,1.271 0.198,0.188 10 false 1 5.177,1.406 7.073,1.646 1.896,0.24 10 false Theft Warning ECU Assembly 2.885,0.865 3.219,1.052 0.333,0.188 10 false G19 2.885,1.031 4.802,1.271 1.917,0.24 10 false Combination Meter Assembly 1.948,1.24 2.281,1.427 0.333,0.188 10 false K4 1.948,1.417 3.594,1.823 1.646,0.406 10 false Front Door Coutesy Light Switch Assembly LH

PROCEDURE

1.CHECK COMBINATION METER ASSEMBLY
a.

When the driver side door is opened/closed, check that the indicator in the combination meter assembly operates normally.

OK:

Indicator operates normally.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER - THEFT WARNING ECU)

NG

3.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH
2.CHECK HARNESS AND CONNECTOR (COMBINATION METER - THEFT WARNING ECU)
a.

Disconnect the G19 combination meter assembly connector.


b.

Disconnect the G29 theft warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G19-17 (DOOR) - G29-7 (CTY) Always Below 1 Ω
G19-17 (DOOR) or G29-7 (CTY) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G19-17 (DOOR) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH
a.
B276106
0.396,1.729 0.667,1.729 0.667,1.729 0.854,1.375 true 0.969,0.208 1.281,0.365 0.313,0.156 10 false *a 0.99,0.656 1.302,0.813 0.313,0.156 10 false *b 0.198,1.635 0.531,1.833 0.333,0.198 10 false *c
*a Not pushed (ON)
*b Pushed (OFF)
*c Body ground


Remove the front door courtesy light switch assembly LH.

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - Body ground Not pushed (ON) Below 1 Ω
Pushed (OFF) 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - FRONT DOOR COURTESY LIGHT SWITCH LH)

NG

REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - FRONT DOOR COURTESY LIGHT SWITCH LH)
a.

Disconnect the G19 combination meter assembly connector.


b.

Disconnect the K4 front door courtesy light switch assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G19-16 (DCTY) - K4-1 Always Below 1 Ω
G19-16 (DCTY) or K4-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR