Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › 2011.10–2012.04
RM1840EF _58 Vehicle Interior _009641 THEFT DETERRENT / KEYLESS ENTRY _0052689 ENGINE IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  B2799  Engine Immobiliser System Malfunction  


DESCRIPTION

This DTC is output when one of the following occurs: 1) the ECM detects errors in its own communications with the transponder key ECU assembly; 2) the ECM detects errors in the communication lines; or 3) the ECU communication ID between the transponder key ECU assembly and ECM is different and an engine start is attempted. Before troubleshooting for this DTC, make sure no transponder key ECU DTCs are present. If present, troubleshoot the transponder key ECU DTCs first.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2799 Engine Immobiliser System Malfunction Either condition is met (1 trip detection logic*1):
·

A malfunction occurs in the communication or communication lines between the ECM and transponder key ECU assembly.

·

A communication code cannot be verified during communication between the ECM and transponder key ECU assembly.


·

Harness or connector

·

Transponder key ECU assembly

·

ECM

·

Telephone transceiver*2


Detection Enabling Condition (DTC Output Confirmation Operation)

Either condition is met:


·

Within 10 seconds of an engine start operation being performed (with the shift lever in P and the brake pedal [for Automatic Transmission] or clutch pedal [for Manual Transmission] depressed, turn the ignition switch to ON). If there is a malfunction, the engine stops (communication begins within 3 seconds of the engine start operation being performed, and DTCs are stored after 6 seconds).

·

10 seconds after the ignition switch is turned to ON after reconnecting the cable to the negative (-) battery terminal (communication begins within 3 seconds of the ignition switch being turned to ON, and DTCs are stored after 6 seconds).



*1: Only output while a malfunction is present.

*2: w/ Blocking System


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started. -

Related Data List and Active Test
DTC Code Data List and Active Test
B2799 -

WIRING DIAGRAM

B294362
0.052,0.031 1.75,0.271 1.698,0.24 12 false w/o Blocking System: 5.479,0.917 5.833,1.073 0.354,0.156 10 false EFIO 5.25,0.844 5.448,1 0.198,0.156 10 false 13 5.479,1.385 5.833,1.542 0.354,0.156 10 false EFII 4.854,1.958 5.208,2.146 0.354,0.188 10 false G26 4.833,2.104 6.917,2.385 2.083,0.281 10 false Transponder Key ECU Assembly 1.167,1.979 1.521,2.135 0.354,0.156 10 false ECM 0.156,2.583 1.854,2.74 1.698,0.156 10 false *1: for 1KD-FTV, 2KD-FTV 0.156,2.854 1.854,3.01 1.698,0.156 10 false *2: for 2TR-FE 0.156,3.125 1.854,3.281 1.698,0.156 10 false *3: for 2TR-FBE 1.813,0.927 2.125,1.083 0.313,0.156 10 false G38 1.813,0.719 2.125,0.875 0.313,0.156 10 false 30*1 1.813,1.406 2.125,1.563 0.313,0.156 10 false G38 1.49,0.938 1.719,1.094 0.229,0.156 10 false IMI 1.448,1.417 1.74,1.573 0.292,0.156 10 false IMO 1.813,1.188 2.125,1.344 0.313,0.156 10 false 29*1 2.208,0.927 2.521,1.083 0.313,0.156 10 false G88 2.198,0.719 2.51,0.875 0.313,0.156 10 false 16*2 2.208,1.406 2.521,1.563 0.313,0.156 10 false G88 2.198,1.188 2.51,1.344 0.313,0.156 10 false 15*2 2.573,0.927 2.938,1.083 0.365,0.156 10 false G146 2.615,0.719 2.927,0.875 0.313,0.156 10 false 31*3 2.573,1.406 2.938,1.563 0.365,0.156 10 false G146 2.615,1.188 2.927,1.344 0.313,0.156 10 false 32*3 5.25,1.323 5.448,1.479 0.198,0.156 10 false 12

B294367
5.823,1.677 6.177,1.833 0.354,0.156 10 false EFIO 5.573,1.615 5.771,1.771 0.198,0.156 10 false 13 5.823,0.781 6.115,0.938 0.292,0.156 10 false EFII 1.083,0.771 1.323,0.927 0.24,0.156 10 false IMI 1.01,1.688 1.302,1.844 0.292,0.156 10 false IMO 0.74,2.073 1.094,2.229 0.354,0.156 10 false ECM 0.083,3.073 1.781,3.229 1.698,0.156 10 false *1: for 1KD-FTV, 2KD-FTV 0.052,0.042 1.573,0.313 1.521,0.271 12 false w/ Blocking System: 5.458,2.052 5.792,2.208 0.333,0.156 10 false G26 5.458,2.208 6.896,2.604 1.438,0.396 10 false Transponder Key ECU Assembly 2.969,2.104 3.354,2.26 0.385,0.156 10 false G144 2.969,2.26 4.406,2.698 1.438,0.438 10 false Telephone Transceiver Assembly 0.083,3.333 1.781,3.49 1.698,0.156 10 false *2: for 2TR-FBE 1.385,1.688 1.698,1.844 0.313,0.156 10 false G38 1.396,0.583 1.708,0.74 0.313,0.156 10 false 30*1 1.385,0.771 1.698,0.927 0.313,0.156 10 false G38 1.396,1.49 1.708,1.646 0.313,0.156 10 false 29*1 1.75,1.688 2.115,1.844 0.365,0.156 10 false G146 1.781,0.573 2.094,0.729 0.313,0.156 10 false 31*2 1.75,0.771 2.115,0.927 0.365,0.156 10 false G146 1.781,1.49 2.094,1.646 0.313,0.156 10 false 32*2 5.573,0.698 5.771,0.854 0.198,0.156 10 false 12 4.292,1.615 4.417,1.771 0.125,0.156 10 false 2 4.292,0.698 4.417,0.854 0.125,0.156 10 false 1 2.844,1.615 2.969,1.771 0.125,0.156 10 false 8 2.844,0.698 2.948,0.854 0.104,0.156 10 false 7 3.875,1.615 4.25,1.771 0.375,0.156 10 false BLK4 3.875,0.698 4.25,0.854 0.375,0.156 10 false BLK1 3.01,1.615 3.385,1.771 0.375,0.156 10 false BLK3 3.01,0.698 3.385,0.854 0.375,0.156 10 false BLK2

CAUTION / NOTICE / HINT

NOTICE:
·

The fixed 12 V power source voltage in the ECM is output through a resistance from terminal IMI. The transponder key ECU assembly grounds or does not ground this power source voltage accordingly.

·

The fixed 12 V power source voltage in the transponder key ECU assembly is output through a resistance from terminal EFII. The ECM grounds or does not ground this power source voltage accordingly.

·

When replacing the transponder key ECU assembly, ECM or telephone transceiver assembly (w/ Blocking System), refer to the Service Bulletin.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



HINT:
w/ Blocking System:
·

When DTC B1587 and B2799 are output simultaneously, perform troubleshooting for DTC B2799 first.

·

After troubleshooting for this DTC, make sure B2799 is not present. If present, troubleshoot the blocking system DTCs next.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61
Powertrain > Engine and ECT > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 61
Powertrain > Engine and ECT > Trouble Codes
50001 234
OK:

DTC B2799 is not output.


Result:
Result Proceed to
OK A
NG (w/ Blocking System) B
NG (w/o Blocking System) C




A

B

3.CHECK BLOCKING SYSTEM

C

4.REREGISTER ECU COMMUNICATION ID
3.CHECK BLOCKING SYSTEM
a.

Check the blocking system setting.

HINT:
·

Check with the customer's contacted service provider to determine whether the blocking system is set.

·

Request that the customer have the service provider unset the blocking system.



Result:
Result Proceed to
Blocking system is unset. A
Blocking system is set B




A

4.REREGISTER ECU COMMUNICATION ID

B

UNSET BLOCKING SYSTEM

4.REREGISTER ECU COMMUNICATION ID
a.

Reregister the ECU - ECM communication ID (Refer to Service Bulletin).


Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61
Powertrain > Engine and ECT > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check for the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 61
Powertrain > Engine and ECT > Trouble Codes
50001 234
OK:

DTC B2799 is not output.



Result:
Proceed to
OK
NG



OK

END (ECU COMMUNICATION ID IS NOT REGISTERED CORRECTLY)

NG

7.CHECK CONNECTION OF CONNECTOR
7.CHECK CONNECTION OF CONNECTOR
a.

Turn the ignition switch off.


b.

Check that the connectors are properly connected to the ECM and transponder key ECU assembly.

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (SFI OR ECD COMMUNICATION LINE)

NG

CONNECT CONNECTOR CORRECTLY

8.CHECK HARNESS AND CONNECTOR (SFI OR ECD COMMUNICATION LINE)
a.

Disconnect the G26 transponder key ECU assembly connector.


b.

Disconnect the G38*1, G88*2 or G146*3 ECM connector.

*1: for 1KD-FTV, 2KD-FTV

*2: for 2TR-FE

*3: for 2TR-FBE



c.

w/ Blocking System:

i.

Disconnect the G144 telephone transceiver assembly connector.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1KD-FTV, 2KD-FTV (w/o Blocking System):
Tester Connection Condition Specified Condition
G26-13 (EFIO) - G38-30 (IMI) Always Below 1 Ω
G26-12 (EFII) - G38-29 (IMO) Always Below 1 Ω
G26-13 (EFIO) or G38-30 (IMI) - Body ground Always 10 kΩ or higher
G26-12 (EFII) or G38-29 (IMO) - Body ground Always 10 kΩ or higher

for 1KD-FTV, 2KD-FTV (w/ Blocking System):
Tester Connection Condition Condition
G26-13 (EFIO) - G144-2 (BLK4) Always Below 1 Ω
G26-12 (EFII) - G144-1 (BLK1) Always Below 1 Ω
G144-8 (BLK3) - G38-30 (IMI) Always Below 1 Ω
G144-7 (BLK2) - G38-29 (IMO) Always Below 1 Ω
G26-13 (EFIO) or G144-2 (BLK4) - Body ground Always 10 kΩ or higher
G26-12 (EFII) or G144-1 (BLK1) - Body ground Always 10 kΩ or higher
G144-8 (BLK3) or G38-30 (IMI) - Body ground Always 10 kΩ or higher
G144-7 (BLK2) or G38-29 (IMO) - Body ground Always 10 kΩ or higher

for 2TR-FE:
Tester Connection Condition Specified Condition
G26-13 (EFIO) - G88-16 (IMI) Always Below 1 Ω
G26-12 (EFII) - G88-15 (IMO) Always Below 1 Ω
G26-13 (EFIO) or G88-16 (IMI) - Body ground Always 10 kΩ or higher
G26-12 (EFII) or G88-15 (IMO) - Body ground Always 10 kΩ or higher

for 2TR-FBE (w/o Blocking System):
Tester Connection Condition Specified Condition
G26-13 (EFIO) - G146-31 (IMI) Always Below 1 Ω
G26-12 (EFII) - G146-32 (IMO) Always Below 1 Ω
G26-13 (EFIO) or G146-31 (IMI) - Body ground Always 10 kΩ or higher
G26-12 (EFII) or G146-32 (IMO) - Body ground Always 10 kΩ or higher

for 2TR-FBE (w/ Blocking System):
Tester Connection Condition Specified Condition
G26-13 (EFIO) - G144-2 (BLK4) Always Below 1 Ω
G26-12 (EFII) - G144-1 (BLK1) Always Below 1 Ω
G144-8 (BLK3) - G146-31 (IMI) Always Below 1 Ω
G144-7 (BLK2) - G146-32 (IMO) Always Below 1 Ω
G26-13 (EFIO) or G144-2 (BLK4) - Body ground Always 10 kΩ or higher
G26-12 (EFII) or G144-1 (BLK1) - Body ground Always 10 kΩ or higher
G144-8 (BLK3) or G146-31 (IMI) - Body ground Always 10 kΩ or higher
G144-7 (BLK2) or G146-32 (IMO) - Body ground Always 10 kΩ or higher



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for 1KD-FTV, 2KD-FTV (w/o Blocking System):
Tester Connection Condition Specified Condition
G26-13 (EFIO) or G38-30 (IMI) - Body ground Always Below 1 V
G26-12 (EFII) or G38-29 (IMO) - Body ground Always Below 1 V

for 1KD-FTV, 2KD-FTV (w/ Blocking System):
Tester Connection Condition Specified Condition
G26-13 (EFIO) or G144-2 (BLK4) - Body ground Always Below 1 V
G26-12 (EFII) or G144-1 (BLK1) - Body ground Always Below 1 V
G144-8 (BLK3) or G38-30 (IMI) - Body ground Always Below 1 V
G144-7 (BLK2) or G38-29 (IMO) - Body ground Always Below 1 V

for 2TR-FE:
Tester Connection Condition Specified Condition
G26-13 (EFIO) or G88-16 (IMI) - Body ground Always Below 1 V
G26-12 (EFII) or G88-15 (IMO) - Body ground Always Below 1 V

for 2TR-FBE (w/o Blocking System):
Tester Connection Condition Specified Condition
G26-13 (EFIO) or G146-31 (IMI) - Body ground Always Below 1 V
G26-12 (EFII) or G146-32 (IMO) - Body ground Always Below 1 V

for 2TR-FBE (w/ Blocking System):
Tester Connection Condition Specified Condition
G26-13 (EFIO) or G144-2 (BLK4) - Body ground Always Below 1 V
G26-12 (EFII) or G144-1 (BLK1) - Body ground Always Below 1 V
G144-8 (BLK3) or G146-31 (IMI) - Body ground Always Below 1 V
G144-7 (BLK2) or G146-32 (IMO) - Body ground Always Below 1 V



Result:
Proceed to
OK
NG



OK

9.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.REPLACE ECM
a.

Result:
Proceed to
NEXT



NEXT

10.REREGISTER ECU COMMUNICATION ID
10.REREGISTER ECU COMMUNICATION ID
a.

Reregister the ECU - ECM communication ID (Refer to Service Bulletin).


Result:
Proceed to
NEXT



NEXT

11.CLEAR DTC
11.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61
Powertrain > Engine and ECT > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

12.CHECK FOR DTC
12.CHECK FOR DTC
a.

Check for the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 61
Powertrain > Engine and ECT > Trouble Codes
50001 234
OK:

DTC B2799 is not output.


Result:
Result Proceed to
OK A
NG (w/o Blocking System) B
NG (w/ Blocking System) C




A

END (ECM IS DEFECTIVE)

B

REPLACE TRANSPONDER KEY ECU ASSEMBLY

C

13.REPLACE TRANSPONDER KEY ECU ASSEMBLY
13.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Temporarily replace the transponder key ECU assembly with a new one (Refer to Service Bulletin).


Result:
Proceed to
NEXT



NEXT

14.REGISTER ECU COMMUNICATION ID
14.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU - ECM communication ID (Refer to Service Bulletin).


Result:
Proceed to
NEXT



NEXT

15.CLEAR DTC
15.CLEAR DTC

NEXT

16.CHECK FOR DTC
16.CHECK FOR DTC

Result:
Proceed to
OK
NG



OK

END (TRANSPONDER KEY ECU IS DEFECTIVE)

NG

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY