Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › BLOCKING SYSTEM › 2011.10–2012.04
RM1840EF _58 Vehicle Interior _009641 THEFT DETERRENT / KEYLESS ENTRY _0052695 BLOCKING SYSTEM U

THEFT DETERRENT / KEYLESS ENTRY  BLOCKING SYSTEM  TERMINALS OF ECU  


CHECK TELEPHONE TRANSCEIVER ASSEMBLY


B236628
3.219,1.083 3.656,1.323 0.438,0.24 3.26,1.125 3.625,1.302 0.365,0.177 10 false G144

a.

Disconnect the G144 telephone transceiver assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G144-6 (IG2) - G144-9 (E) B-O - W-B Ignition switch Ignition switch ON 11 to 14 V
G144-9 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω
G144-12 (+B) - G144-9 (E) L-Y - W-B Power supply Always 11 to 14 V

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the G144 telephone transceiver assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G144-1 (BLK1) - G144-9 (E) Y-B - W-B Transponder key ECU assembly output signal Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected. Pulse generation (See waveform 1)
G144-2 (BLK4) - G144-9 (E) Y-G - W-B Transponder key ECU assembly input signal Ignition switch off Below 1 V
Ignition switch ON Pulse generation (See waveform 2)
G144-7 (BLK2) - G144-9 (E) Y-B - W-B ECM input signal Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected. Pulse generation (See waveform 1)
G144-8 (BLK3) - G144-9 (E) Y-G - W-B ECM output signal Ignition switch off Below 1 V
Ignition switch ON Pulse generation (See waveform 2)

If the result is not as specified, the telephone transceiver assembly may have a malfunction.



e.
B343084
0.094,0.875 0.552,1.073 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 1.

Waveform 1 (Reference)
Item Content
Tester Connection
·

G144-1 (BLK1) - G144-9 (E)

·

G144-7 (BLK2) - G144-9 (E)


Tool Setting 5 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.


f.
B344646
0.323,1.125 0.781,1.323 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 2.

Waveform 2 (Reference)
Item Content
Tester Connection
·

G144-2 (BLK4) - G144-9 (E)

·

G144-8 (BLK3) - G144-9 (E)


Tool Setting 10 V/DIV., 100 ms./DIV.
Condition Ignition switch ON



CHECK TRANSPONDER KEY ECU ASSEMBLY


B276309
1.323,0.396 1.906,0.74 0.583,0.344 1.49,0.479 1.833,0.688 0.344,0.208 10 false G26

a.

Disconnect the G26 transponder key ECU assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
G26-16 (GND) - Body ground - G - Body ground Ground Always Below 1 Ω -
G26-1 (+B) - G26-16 (GND) Input L-Y - G Battery Always 11 to 14 V +B
G26-2 (IG) - G26-16 (GND) Input B-O - G Ignition switch Ignition switch off Below 1 V IG SW
Ignition switch ON 11 to 14 V
G26-3 (KSW) - G26-16 (GND) Input BR - G Unlock warning switch No key in ignition key cylinder 10 kΩ or higher Key SW/B2780
Key inserted in ignition key cylinder Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the G26 transponder key ECU assembly connector.


d.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
G26-14 (VC5) - G26-16 (GND) Input L - G Transponder key amplifier power supply No key in ignition key cylinder Below 1 V
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number


(If immobiliser key code certification communication is not performed correctly, the malfunction may be indicated by one or more of the Data List items listed above)
Key inserted in ignition key cylinder 4.6 to 5.4 V
G26-4 (TXCT) - G26-16 (GND) Input L-B - G Key code output signal No key in ignition key cylinder Below 1 V
Key inserted in ignition key cylinder Pulse generation (See waveform 1)
G26-15 (CODE) - G26-16 (GND) Output L-Y - G Demodulated signal of key code data No key in ignition key cylinder Below 1 V
Key inserted in ignition key cylinder Pulse generation (See waveform 2)
G26-7 (CTY) - G26-16 (GND) Input R-B - G Front door courtesy light switch (for Driver Side) Driver door closed 10 kΩ or higher D Door Courtesy SW
Driver door open Below 1 Ω
G26-13 (EFIO) - G26-16 (GND) Input Y-G - G ECM output signal Ignition switch off Below 1 V E/G Start Permission
Ignition switch ON Pulse generation (See waveform 3)
G26-12 (EFII) - G26-16 (GND) Output Y-B - G ECM input signal Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected Pulse generation (See waveform 4) E/G Start Permission
G26-8 (IND) - G26-16 (GND) Output G-R - G Security indicator light signal Immobiliser set Alternating between 11 to 14 V and below 1 V -
Immobiliser unset Below 1 V
G26-9 (D) - G26-16 (GND) Input/Output B - G Diagnosis tester communication Always Pulse generation -
G26-5 (AGND) - Body ground - L-O - Body ground Transponder key amplifier ground Always Below 1 Ω -

If the result is not as specified, the transponder key ECU assembly may have a malfunction.



e.
B343083
0.313,1.083 0.771,1.281 0.458,0.198 10 false GND

Inspect using an oscilloscope.

HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection G26-4 (TXCT) - G26-16 (GND)
Tool Setting 5 V/DIV., 20 ms./DIV.
Condition Key inserted in ignition key cylinder


ii.
B343082
0.302,1.021 0.76,1.219 0.458,0.198 10 false GND

Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection G26-15 (CODE) - G26-16 (GND)
Tool Setting 5 V/DIV., 20 ms./DIV.
Condition Key inserted in ignition key cylinder


iii.
B237527
2.802,0.552 3.208,0.771 0.406,0.219 10 false GND

Waveform 3 (Reference)

Measurement Condition
Item Content
Tester Connection G26-13 (EFIO) - G26-16 (GND)
Tool Setting 10 V/DIV., 100 ms./DIV.
Condition Ignition switch ON


iv.
B229710
0.198,0.74 0.563,0.938 0.365,0.198 10 false GND

Waveform 4 (Reference)

Measurement Condition
Item Content
Tester Connection G26-12 (EFII) - G26-16 (GND)
Tool Setting 5 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected




CHECK ECM (for 2TR-FBE)


B286952
1.135,0.125 1.615,0.406 0.479,0.281 1.948,0.125 2.427,0.406 0.479,0.281 3.156,0.125 3.635,0.406 0.479,0.281 3.875,0.125 4.354,0.406 0.479,0.281 4.594,0.125 5.073,0.406 0.479,0.281 5.49,0.125 5.969,0.406 0.479,0.281 1.198,0.177 1.594,0.354 0.396,0.177 10 false G145 2.01,0.177 2.427,0.396 0.417,0.219 10 false G146 3.271,0.177 3.625,0.365 0.354,0.188 10 false C95 4,0.177 4.333,0.375 0.333,0.198 10 false C96 4.708,0.177 5.063,0.385 0.354,0.208 10 false C97 5.604,0.188 5.938,0.385 0.333,0.198 10 false C98

a.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G146-32 (IMO) - Body ground Y-B - Body ground Transponder key ECU assembly output signal Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected. Pulse generation (See waveform 1)
G146-31 (IMI) - Body ground Y-G -Body ground Transponder key ECU assembly input signal Ignition switch off Below 1 V
Ignition switch ON Pulse generation (See waveform 2)

If the result is not as specified, the ECM may have a malfunction.



b.

Inspect using an oscilloscope.

HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B343084
0.094,0.875 0.552,1.073 0.458,0.198 10 false GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection G146-32 (IMO) - Body ground
Tool Setting 5 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.


ii.
B237527
2.802,0.552 3.188,0.74 0.385,0.188 10 false GND

Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection G146-31 (IMI) - Body ground
Tool Setting 10 V/DIV., 100 ms./DIV.
Condition Ignition switch ON




CHECK ECM (for 1KD-FTV, 2KD-FTV)


B236632
1.26,0.104 1.74,0.385 0.479,0.281 2.625,0.104 3.104,0.385 0.479,0.281 4.146,0.104 4.625,0.385 0.479,0.281 5.406,0.104 5.885,0.385 0.479,0.281 1.375,0.156 1.719,0.354 0.344,0.198 10 false C22 2.74,0.156 3.031,0.354 0.292,0.198 10 false C23 4.26,0.156 4.552,0.354 0.292,0.198 10 false G38 5.521,0.156 5.823,0.354 0.302,0.198 10 false G39

a.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G38-29 (IMO) - Body ground Y-B - Body ground Transponder key ECU assembly output signal Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected. Pulse generation (See waveform 1)
G38-30 (IMI) - Body ground Y-G -Body ground Transponder key ECU assembly input signal Ignition switch off Below 1 V
Ignition switch ON Pulse generation (See waveform 2)

If the result is not as specified, the ECM may have a malfunction.



b.

Inspect using an oscilloscope.

HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B343084
0.094,0.875 0.552,1.073 0.458,0.198 10 false GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection G38-29 (IMO) - Body ground
Tool Setting 5 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.


ii.
B237527
2.802,0.552 3.167,0.719 0.365,0.167 10 false GND

Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection G38-30 (IMI) - Body ground
Tool Setting 10 V/DIV., 100 ms./DIV.
Condition Ignition switch ON