Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2011.10–2012.04
RM1840EF _58 Vehicle Interior _009643 METER / GAUGE / DISPLAY _0052702 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Tachometer Malfunction  


DESCRIPTION

In this circuit, the combination meter assembly receives engine speed signals from the ECM. The meter CPU displays the engine speed, which is calculated based on the data received from the ECM.

WIRING DIAGRAM

E273487
0.844,1.115 1.292,1.313 0.448,0.198 10 false TACH 1.417,0.875 1.667,1.063 0.25,0.188 10 false 1*1 1.844,0.875 2.177,1.063 0.333,0.188 10 false 29*2 2.365,0.875 2.667,1.063 0.302,0.188 10 false 4*3 1.396,1.094 1.688,1.281 0.292,0.188 10 false G88 1.823,1.094 2.198,1.281 0.375,0.188 10 false G146 2.323,1.094 2.625,1.281 0.302,0.188 10 false G39 0.552,2.083 1,2.281 0.448,0.198 10 false ECM 0.198,2.667 1.438,2.917 1.24,0.25 10 false *1: for 2TR-FE 0.198,2.958 1.438,3.208 1.24,0.25 10 false *2: for 2TR-FBE 0.198,3.24 1.906,3.49 1.708,0.25 10 false *3: for 1KD-FTV, 2KD-FTV 5.854,2.167 6.302,2.365 0.448,0.198 10 false G19 5.875,2.344 7.073,2.781 1.198,0.438 10 false Combination Meter Assembly 5.74,0.969 5.906,1.177 0.167,0.208 10 false 7 5.948,1.104 6.396,1.302 0.448,0.198 10 false S

PROCEDURE

1.CHECK COMBINATION METER ASSEMBLY
a.
E236122
1.438,0.313 1.969,0.594 0.531,0.281 1.24,1.208 0.74,0.615 true 2.813,3.427 3.156,3.583 0.344,0.156 10 false GND 0.052,0.021 0.219,0.188 0.167,0.167 10 false *a 0.615,0.49 0.74,0.646 0.125,0.156 10 false S 1.573,0.375 1.854,0.542 0.281,0.167 10 false G19
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the G19 combination meter assembly connector.


b.

Using an oscilloscope, check the signal waveform of the meter.

Item Content
Tester Connection G19-7 (S) - Body ground
Tool Setting 5 V/DIV., 10 msec./DIV.
Condition Engine idling

HINT:

As the engine speed increases, the wavelength shortens.


OK:

The waveform displayed is as shown in the illustration.



Result:
Proceed to
OK
NG



OK

CHECK ENGINE TYPE

NG

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the G19 combination meter assembly connector.


b.

Disconnect the G88*1, G146*2 or G39*3 ECM connector.

*1: for 2TR-FE

*2: for 2TR-FBE

*3: for 1KD-FTV, 2KD-FTV



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2TR-FE
Tester Connection Condition Specified Condition
G19-7 (S) - G88-1 (TACH) Always Below 1 Ω
G19-7 (S) or G88-1 (TACH) - Body ground Always 10 kΩ or higher


for 2TR-FBE
Tester Connection Condition Specified Condition
G19-7 (S) - G146-29 (TACH) Always Below 1 Ω
G19-7 (S) or G146-29 (TACH) - Body ground Always 10 kΩ or higher

for 1KD-FTV, 2KD-FTV
Tester Connection Condition Specified Condition
G19-7 (S) - G39-4 (TACH) Always Below 1 Ω
G19-7 (S) or G39-4 (TACH) - Body ground Always 10 kΩ or higher

Result:
Result Proceed to
OK (for 2TR-FE, 2TR-FBE) A
OK (for 1KD-FTV) B
OK (for 2KD-FTV) C
NG D




A

3.CHECK ENGINE TYPE

B

4.CHECK ENGINE TYPE

C

5.CHECK ENGINE TYPE

D

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK ENGINE TYPE
a.

Check the engine type.

Result:
Result Proceed to
for 2TR-FE, w/ Secondary Air Injection System A
for 2TR-FE, w/o Secondary Air Injection System B
for 2TR-FBE C




A

B

C

4.CHECK ENGINE TYPE
a.

Check the engine type.

Result:
Result Proceed to
for 1KD-FTV, w/ EGR Cooler A
for 1KD-FTV, w/o EGR Cooler B




A

B

5.CHECK ENGINE TYPE
a.

Check the engine type.

Result:
Result Proceed to
for 2KD-FTV, w/ EGR Cooler A
for 2KD-FTV, w/o EGR Cooler B




A

B