Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2011.10–2012.01
RM1840EF _58 Vehicle Interior _009645 SUPPLEMENTAL RESTRAINT SYSTEMS _0052709 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  SRS Warning Light Remains ON  


DESCRIPTION

The SRS warning light is located on the combination meter. When the ignition switch is turned from off to ON, the SRS warning light illuminates. If the SRS is normal, the SRS warning light turns off automatically after approximately 6 seconds. If there is a malfunction in the SRS, the SRS warning light remains illuminated even after approximately 6 seconds have passed. When terminals TC and CG of the DLC3 are connected, the DTCs are communicated through SRS warning light blinking patterns.

WIRING DIAGRAM

C237174
3.792,2.083 4.229,2.229 0.438,0.146 10 false SW 3.188,2.667 3.625,2.813 0.438,0.146 10 false IG+ 3.188,4.25 3.625,4.396 0.438,0.146 10 false EP 3.052,5.625 3.354,5.792 0.302,0.167 10 false G19 5.75,5.594 6.083,5.76 0.333,0.167 10 false G53 0.177,0.875 1.448,1.083 1.271,0.208 10 false from Ignition Switch 2.135,1.01 2.479,1.177 0.344,0.167 10 false IGN 2.104,2.823 2.458,2.99 0.354,0.167 10 false MET 2.906,2.563 3.156,2.771 0.25,0.208 10 false 21 2.906,4.146 3.115,4.354 0.208,0.208 10 false 22 6.146,2.083 6.583,2.229 0.438,0.146 10 false LA 4.135,1.958 4.406,2.125 0.271,0.167 10 false 20 5.875,1.958 6.135,2.146 0.26,0.188 10 false 14 5.885,3.573 6.094,3.781 0.208,0.208 10 false 25 5.875,4.167 6.104,4.354 0.229,0.188 10 false 26 6.146,3.677 6.354,3.833 0.208,0.156 10 false E1 6.146,4.271 6.385,4.438 0.24,0.167 10 false E2 5.885,0.76 6.063,0.917 0.177,0.156 10 false 21 6.146,0.875 6.5,1.031 0.354,0.156 10 false IG2 3.052,5.792 4.823,5.979 1.771,0.188 10 false Combination Meter 5.75,5.75 7.115,5.958 1.365,0.208 10 false Center Airbag Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.INSPECT BATTERY
a.

Measure the voltage of the battery.

Standard voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTION OF CONNECTOR

NG

RECHARGE OR REPLACE BATTERY

2.CHECK CONNECTION OF CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and combination meter.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF CENTER AIRBAG SENSOR)

NG

CONNECT CONNECTORS PROPERLY

3.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF CENTER AIRBAG SENSOR)
a.
C198548
0.385,0.698 0.823,0.99 0.438,0.292 1.594,1.417 1.302,1.927 true 1.74,1.417 2.135,1.917 true 2.219,1.313 2.646,1.313 true 0.479,0.76 0.792,0.917 0.313,0.156 10 false G53 1.188,1.938 1.438,2.125 0.25,0.188 10 false E2 2.094,1.927 2.323,2.094 0.229,0.167 10 false E1 2.698,1.24 2.99,1.406 0.292,0.167 10 false IG2 1.573,0.198 1.792,0.365 0.219,0.167 10 false *a
*a Rear view of wire harness connector
(to Center Airbag Sensor)


Disconnect the connector from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Operate all the components of the electrical system (defogger, wipers, headlights, heater blower, etc.).


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G53-21 (IG2) - Body ground Ignition switch ON 11 to 14 V



f.

Turn the ignition switch off.


g.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G53-25 (E1) - Body ground Always Below 1 Ω
G53-26 (E2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF COMBINATION METER)

NG

REPLACE HARNESS AND CONNECTOR

4.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF COMBINATION METER)
a.
H100390
1.448,0.385 1.875,0.667 0.427,0.281 0.677,1.396 0.375,1.76 true 0.781,1.406 1.01,1.76 true 1.531,0.438 1.833,0.635 0.302,0.198 10 false G19 0.094,0.063 0.281,0.26 0.188,0.198 10 false *a 0.135,1.708 0.396,1.906 0.26,0.198 10 false IG+ 1.052,1.708 1.313,1.906 0.26,0.198 10 false EP
*a Front view of wire harness connector
(to Combination Meter)


Disconnect the G19 connector from the combination meter.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G19-21 (IG+) - Body ground Ignition switch ON 11 to 14 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G19-22 (EP) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (CENTER AIRBAG SENSOR - COMBINATION METER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (CENTER AIRBAG SENSOR - COMBINATION METER)
a.
H100391
0.24,1.5 0.656,1.75 0.417,0.25 0.24,3.083 0.656,3.333 0.417,0.25 1.906,1.625 2.75,2.292 true 2.865,3.656 3.052,3.51 true 0.094,0.229 0.302,0.469 0.208,0.24 10 false *a 0.094,2.625 0.313,2.833 0.219,0.208 10 false *b 2.802,2.229 3.063,2.438 0.26,0.208 10 false LA 3.094,3.417 3.354,3.625 0.26,0.208 10 false SW 0.323,1.542 0.635,1.75 0.313,0.208 10 false G53 0.323,3.125 0.604,3.333 0.281,0.208 10 false G19
*a Rear view of wire harness connector
(to Center Airbag Sensor)
*b Front view of wire harness connector
(to Combination Meter)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G53-14 (LA) - G19-20 (SW) Always Below 1 Ω
G53-14 (LA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK SRS WARNING LIGHT (OPERATION)

NG

REPLACE HARNESS AND CONNECTOR

6.CHECK SRS WARNING LIGHT (OPERATION)
a.

Connect the connector to the combination meter.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 second.


c.

Turn the ignition switch to ON.


d.

Check the SRS warning light condition.

NOTICE:

Make sure that nobody is in the vehicle.


OK:

After the primary check period, the SRS warning light goes off for approximately 10 seconds and then remains on.


HINT:

The primary check period is approximately 6 seconds after the ignition switch is turned to ON.



Result:
Proceed to
OK
NG



OK

7.CHECK CENTER AIRBAG SENSOR ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY

7.CHECK CENTER AIRBAG SENSOR ASSEMBLY
a.
C198548
0.385,0.729 0.823,1.021 0.438,0.292 1.844,1.177 2.521,1.563 true 0.479,0.792 0.792,0.948 0.313,0.156 10 false G53 2.563,1.5 2.854,1.667 0.292,0.167 10 false LA 1.573,0.229 1.792,0.396 0.219,0.167 10 false *a
*a Rear view of wire harness connector
(to Center Airbag Sensor)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G53-14 (LA) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.REPLACE CENTER AIRBAG SENSOR ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY

8.REPLACE CENTER AIRBAG SENSOR ASSEMBLY
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.



d.

Check the SRS warning light condition.

OK:

SRS warning light illuminates normally.



Result:
Proceed to
OK
NG



OK

END (CENTER AIRBAG SENSOR IS DEFECTIVE)

NG

REPLACE COMBINATION METER ASSEMBLY