Wear protective gloves. Sharp areas on the parts may injure your hands.
1.REMOVE RECLINING POWER SEAT SWITCH KNOB
| *1 | Protective Tape |
Apply protective tape around the front seat cushion shield.
Using a screwdriver, detach the 2 claws and remove the reclining power seat switch knob.
Tape the screwdriver tip before use.
2.REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB
| *1 | Protective Tape |
Apply protective tape around the front seat cushion shield.
Using a screwdriver, detach the 4 claws and remove the slide and vertical power seat switch knob.
Tape the screwdriver tip before use.
3.REMOVE FRONT SEAT CUSHION SHIELD LH
Remove the 2 screws.
Remove the 3 screws.
Detach the claw and guide.
Remove the front seat cushion shield LH with the front inner No. 1 seat cushion shield LH.
4.REMOVE FRONT INNER NO. 1 SEAT CUSHION SHIELD LH
Remove the 2 screws.
Detach the 2 claws and remove the front inner No. 1 seat cushion shield LH.
5.REMOVE FRONT POWER SEAT SWITCH LH
6.REMOVE FRONT SEAT INNER CUSHION SHIELD LH
Remove the screw.
Detach the claw and guide.
Pull the front seat inner cushion shield LH to detach the claw and remove the front seat inner cushion shield LH.
7.REMOVE FRONT SEAT INNER BELT ASSEMBLY LH
8.REMOVE FRONT SEAT CUSHION COVER LH
Remove the front seat cushion cover LH.
9.REMOVE FRONT SEAT CUSHION COVER WITH PAD
Remove the hog rings.
Bend the 2 front seat cushion frame claws upward.
Detach the hooks and remove the front seat cushion cover with pad.
10.REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER
Remove the hog rings and separate type front seat cushion cover from the separate type front seat cushion pad.
11.REMOVE SEPARATE TYPE FRONT SEATBACK COVER
Disconnect the No. 2 seat wire connector and detach the wire harness clamp.
Remove the hog rings from the wires of the separate type front seatback cover, and then roll up the separate type front seatback cover.
Pass the No. 2 seat wire through the hole of the separate type front seatback cover.
Remove the hog rings and detach the strap of the separate type front seatback cover, and then roll up the separate type front seatback cover and No. 1 seatback cloth.
Pass the strap of the separate type front seatback cover through the holes of the separate type front seatback pad.
Remove the hog rings and roll up the separate type front seatback cover.
| *a | Front view of front seatback | *b | Rear view of front seatback |
Detach the 4 claws and remove the 2 front seat headrest support assemblies and separate type front seatback cover from the separate type front seatback pad.
12.REMOVE SEPARATE TYPE FRONT SEATBACK PAD
Remove the separate type front seatback pad.
13.REMOVE NO. 1 SEATBACK CLOTH
Remove the No. 1 seatback cloth.
14.REMOVE RECLINING ADJUSTER INSIDE COVER RH
Remove the screw.
Detach the claw and remove the reclining adjuster inside cover RH.
15.REMOVE RECLINING ADJUSTER INSIDE COVER RH
Remove the screw.
Detach the guide and remove the reclining adjuster inside cover RH.
16.REMOVE RECLINING ADJUSTER INSIDE COVER LH
Remove the screw.
Detach the claw and remove the reclining adjuster inside cover LH.
17.REMOVE RECLINING ADJUSTER INSIDE COVER LH
Remove the screw.
Detach the guide and remove the reclining adjuster inside cover LH.
18.REMOVE POWER SEAT MOTOR ASSEMBLY (for Reclining)
19.REMOVE POWER SEAT MOTOR ASSEMBLY (for Slide)
20.REMOVE POWER SEAT MOTOR ASSEMBLY (for Rear Lifter)
21.REMOVE FRONT LOWER SEAT CUSHION SHIELD RH
Remove the screw.
Detach the 4 claws to and remove the front lower seat cushion shield RH.
22.REMOVE FRONT LOWER SEAT CUSHION SHIELD LH
Remove the screw.
Detach the 4 claws and remove the front lower seat cushion shield LH.
23.REMOVE FRONT SEAT WIRE LH
Detach the wire harness clamp.
Detach the 2 claws and remove the front seat wire LH.
24.REMOVE NO. 2 SEAT WIRE
Detach the 2 wire harness clamps and remove the No. 2 seat wire.
25.REMOVE SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY
Remove the 4 bolts and separate type front seatback spring assembly.