Home › Vehicle Interior › SEAT › REAR SEAT ASSEMBLY(for Double Cab)
RM1840EF _58 Vehicle Interior _009646 SEAT _0052719 REAR SEAT ASSEMBLY(for Double Cab) A

SEAT  REAR SEAT ASSEMBLY(for Double Cab)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


PROCEDURE

Hide 1.INSTALL FOLD SEAT STOPPER BAND ASSEMBLY

a.
B276907
1.51,0.25 1.698,0.25 1.698,0.25 1.76,0.51 false 1.354,0.156 1.51,0.313 0.156,0.156 10 false *1
*1 No. 1 Seat Cushion Frame Lock Plate


Connect and rotate a new connecting wire to the No. 1 seat cushion frame lock plate.


b.
B277847

Connect the fold seat stopper band assembly to the connecting wire.


c.
B276905

Using needle nose pliers, bend the ends of the connecting wire together.


d.
B276901

Return the fold seat stopper band assembly to its original position.


Hide 2.INSTALL NO. 1 SEAT CUSHION PAD

a.
B276899

Install the No. 1 seat cushion pad to the No. 1 seat cushion frame.


Hide 3.INSTALL NO. 1 SEAT CUSHION COVER

a.
B276895

Pass the fold seat stopper band assembly through the 2 holes of the No. 1 seat cushion cover to the surface.


b.
B276897
2.094,2.719 1.813,2.719 1.813,2.719 1.813,3.708 false 2.125,2.615 2.302,2.771 0.177,0.156 10 false *1
*1 Hog Ring Pliers


Using hog ring pliers, install the center of the No. 1 seat cushion cover to the No. 1 seat cushion pad with new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




c.

Close the 2 fasteners.


d.
B276892
2.083,2.885 1.844,2.885 1.844,2.885 1.844,3.677 false 2.115,2.781 2.375,3 0.26,0.219 10 false *1
*1 Hog Ring Pliers


Using hog ring pliers, attach the 2 wires at the rear of the No. 1 seat cushion cover with new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




Hide 4.INSTALL REAR SEAT CUSHION

a.

Install the 2 rear seat cushions with the 2 screws.


Hide 5.INSTALL NO. 1 SEATBACK PAD

a.
B276890

Install a new No. 1 seatback pad to the No. 1 seatback frame.


Hide 6.INSTALL NO. 1 SEATBACK COVER

a.
B276888
2.073,2.896 1.823,2.896 1.823,2.896 1.823,3.698 false 2.115,2.802 2.281,2.958 0.167,0.156 10 false *1
*1 Hog Ring Pliers


Using hog ring pliers, install the center of the No. 1 seatback cover to the No. 1 seatback pad with new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




b.
B276883
1.938,3.229 1.771,3.229 1.771,3.229 1.771,3.865 false 1.979,3.156 2.219,3.354 0.24,0.198 10 false *1
*1 Hog Ring Pliers


Using hog ring pliers, install the No. 1 seatback cover to the No. 1 seatback frame with new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




Hide 7.INSTALL REAR SEATBACK ASSEMBLY

a.

Temporarily install the rear seatback assembly to the rear seat cushion assembly with the 2 bolts.


b.

Tighten the 2 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 8.INSTALL REAR SEAT HEADREST SUPPORT

a.
B276886

Attach the 8 claws to install the 4 rear seat headrest support.


Hide 9.INSTALL REAR SEAT CUSHION COVER LH

B276910
0.844,1.802 0.719,1.677 0.719,1.677 0.552,1.677 false 0.375,1.573 0.604,1.792 0.229,0.219 10 false a
*a Washer installed between rear seat leg bracket LH and rear seat cushion cover LH


a.

Attach the guide.


b.

Install the rear seat cushion cover LH with the screw.


c.

If the washer was installed between the rear seat leg bracket LH and rear seat cushion cover LH:

Install the washer.


Hide 10.INSTALL REAR SEAT LEG BRACKET LH

B276884
1.146,0.979 1.354,0.979 1.354,0.979 1.531,1.344 true 0.865,0.885 1.115,1.063 0.25,0.177 10 false *a
*a Washer installed between nut and rear seat leg bracket LH


a.

If the washer was installed between the nut and rear seat leg bracket LH:

Temporarily install the rear seat leg bracket LH and washer with the nut.


b.

If the washer was not installed between the nut and rear seat leg bracket LH:

Temporarily install the rear seat leg bracket LH with the nut.


c.

Tighten the nut.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


Hide 11.INSTALL REAR SEAT CUSHION COVER RH

HINT:

Use the same procedures described for the LH side.


Hide 12.INSTALL REAR SEAT LEG BRACKET RH

HINT:

Use the same procedures described for the LH side.


Hide 13.INSTALL REAR SEAT HEADREST ASSEMBLY

a.

Install the 2 rear seat headrests.