Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR(for 1KD-FTV, 2KD-FTV)
RM1840EF _58 Vehicle Interior _009648 HEATING / AIR CONDITIONING _0052748 COMPRESSOR(for 1KD-FTV, 2KD-FTV) A

HEATING / AIR CONDITIONING  COMPRESSOR(for 1KD-FTV, 2KD-FTV)  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL MAGNET CLUTCH ASSEMBLY

E171826

a.

Install the magnet clutch stator with the parts aligned as shown in the illustration.


b.
E155204

Using a snap ring expander, install a new snap ring with the chamfered side facing outward.


c.

Attach the connector clamp.


d.
E155205

Using a snap ring expander, install the magnet clutch rotor and a new snap ring with the chamfered side facing outward.

NOTICE:

Do not damage the seal cover of the bearing when installing the snap ring.



e.

Install the magnet clutch washer(s) and magnet clutch hub.

NOTICE:

Do not change the combination of magnet clutch washer(s) used before disassembly.



f.

Connect the battery to the magnet clutch assembly as shown in the illustration to fix the hub and rotor in place.


g.

Wrap the drive belt around the rotor and securely hold it in place by hand.


h.
E171827
1.938,2.74 2.385,2.74 false 1.729,2.656 1.927,2.844 0.198,0.188 10 false *1
*1 Battery


Install the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)

NOTICE:
·

Make sure that there is no foreign matter or oil on the compressor shaft, bolt and clutch hub.

·

When reusing the drive belt, check the belt for wear, cracks or other signs of damage.




Hide 2.INSTALL COOLER BRACKET

a.

Connect the ground wire and install the cooler bracket with the screw.


Hide 3.INSPECT MAGNET CLUTCH CLEARANCE

E171828
1.094,2.333 1.094,1.083 1.094,1.083 1.438,1.083 false 0.833,3.927 1.333,3.927 1.333,3.927 1.333,4.125 false 3.042,4.115 3.042,3.896 false 0.094,0.094 0.313,0.281 0.219,0.188 10 false *a 1.5,1 1.677,1.177 0.177,0.177 10 false *1 1.271,4.156 1.448,4.333 0.177,0.177 10 false *2 2.979,4.156 3.156,4.333 0.177,0.177 10 false *3
*1 Magnet Clutch Hub
*2 Dial Indicator
*3 Battery
*a Component without harness connected
(Magnet Clutch Assembly)


a.

Clamp the cooler compressor in a vise between aluminum plates.


b.

Set a dial indicator to the magnet clutch hub.


c.

Connect the battery positive (+) lead to terminal 1 of the magnet clutch connector. Turn the magnet clutch on and off by connecting and disconnecting the battery negative (-) lead to and from the ground wire, and measure the clearance.

Standard clearance:

0.25 to 0.50 mm (0.010 to 0.020 in.)


If the measured value is not within the standard clearance, remove the magnet clutch hub and adjust the clearance using magnet clutch washers to obtain the standard clearance.

Magnet clutch washer thickness:

0.1 mm (0.004 in.)

0.3 mm (0.012 in.)

0.5 mm (0.020 in.)


NOTICE:

Adjustment should be performed with 3 or less magnet clutch washers.



d.

Remove the cooler compressor from the vise.