Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) › from 2012.04
RM1840EF _58 Vehicle Interior _009648 HEATING / AIR CONDITIONING _0052762 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) U

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  TERMINALS OF ECU  


CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


E224847
2.865,0.135 3.26,0.365 0.396,0.229 4.417,0.135 4.813,0.365 0.396,0.229 2.938,0.167 3.25,0.323 0.313,0.156 10 false G94 4.49,0.167 4.833,0.375 0.344,0.208 10 false G95

a.

Disconnect the G94 air conditioning amplifier assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G94-1 (GND) - Body ground L - Body ground Ground Always Below 1 Ω
G94-5 (+B1) - G94-1 (GND) L-Y - L Battery power source Always 11 to 14 V
G94-6 (IG+) - G94-1 (GND) R-Y - L IG power source Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
G94-13 (MGC) - Body ground B - Body ground Magnet clutch signal Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
G94-14 (HR) - Body ground L-W - Body ground No. 1 heater relay signal Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the G94 air conditioning amplifier assembly connector.


d.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G94-2 (BLW) - Body ground L-B - Body ground Blower motor speed control voltage
·

Ignition switch ON

·

Blower switch on (LO level)


Pulse generation
(See waveform 1)
G94-3 (AOF) - G94-1 (GND) Y-B - L Mode damper servo operation voltage
·

Ignition switch ON

·

Blower switch on (LO level)

·

Mode switch DEF


Below 1 V
·

Ignition switch ON

·

Blower switch on (LO level)

·

Mode switch FACE


11 to 14 V
G94-4 (AOD) - G94-1 (GND) R-B - L Mode damper servo operation voltage
·

Ignition switch ON

·

Blower switch on (LO level)

·

Mode switch FACE


Below 1 V
·

Ignition switch ON

·

Blower switch on (LO level)

·

Mode switch DEF


11 to 14 V
G94-7 (ACT) - G94-1 (GND) R-L - L Magnet clutch on permit input signal
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch off or on (magnet clutch off)


11 to 14 V
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch on (magnet clutch on)


Below 1 V
G94-9 (SPD) - Body ground V-W - Body ground Vehicle speed signal Driving at approximately 20 km/h (12 mph) Pulse generation
(See waveform 2)
G94-13 (MGC) - Body ground B - Body ground Magnet clutch signal
·

Engine idling

·

A/C switch on (magnet clutch on permitted)


Below 1 V
·

Engine idling

·

A/C switch off or on (magnet clutch not on permitted)


11 to 14 V
G94-17 (AMH) - G94-1 (GND) L - L Air mix damper servo operation signal
·

Ignition switch ON

·

Blower switch on (LO level)

·

Temperature switch MAX HOT


11 to 14 V
·

Ignition switch ON

·

Blower switch on (LO level)

·

Temperature switch MAX COLD


Below 1 V
G94-18 (TAMO) - G94-1 (GND) P - L Ambient temperature signal Ignition switch ON Pulse generation
G94-19 (AMC) - G94-1 (GND) R-W - L Air mix damper servo operation signal
·

Ignition switch ON

·

Blower switch on (LO level)

·

Temperature switch MAX HOT


Below 1 V
·

Ignition switch ON

·

Blower switch on (LO level)

·

Temperature switch MAX COLD


11 to 14 V
G94-21 (AC1) - G94-1 (GND) Y - L Idle-up request signal
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch off


11 to 14 V
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch on


Below 1 V
G94-22 (AIR) - G94-1 (GND) L-W - L Recirculation damper servo operation voltage
·

Ignition switch ON

·

Blower switch on (LO level)

·

Fresh switch on


Below 1 V
·

Ignition switch ON

·

Blower switch on (LO level)

·

Recirculation switch on


11 to 14 V
G94-23 (AIF) - G94-1 (GND) G-Y - L Recirculation damper servo operation voltage
·

Ignition switch ON

·

Blower switch on (LO level)

·

Recirculation switch on


Below 1 V
·

Ignition switch ON

·

Blower switch on (LO level)

·

Fresh switch on


11 to 14 V
G95-1 (TE) - G95-14 (SG-4) G - P No. 1 cooler thermistor signal
·

Ignition switch ON

·

Evaporator temperature 0°C (32°F)


2.0 to 2.4 V
·

Ignition switch ON

·

Evaporator temperature 15°C (59°F)


1.4 to 1.8 V
G95-2 (S5-3) - G94-1 (GND) W-R - L Power supply for solar sensor Ignition switch ON 4.5 to 5.5 V
G95-5 (PSW) - G94-1 (GND) Y-B - L Air conditioner pressure sensor signal
·

Engine idling

·

Refrigerant pressure normal


Below 1 V
·

Engine idling

·

Refrigerant pressure less than 0.196 MPa (2.0 kgf/cm2, 28 psi) or more than 3.14 MPa (32.0 kgf/cm2, 455 psi)


11 to 14 V
G95-7 (TS) - G95-2 (S5-3) L-W - W-R Solar sensor signal
·

Ignition switch ON

·

Solar sensor subjected to electric light

·

Vehicle indoors


0.8 to 4.3 V
·

Ignition switch ON

·

Solar sensor covered with cloth

·

Vehicle indoors


Below 0.8 V
G95-9 (VER) - Body ground R - Body ground Steering wheel location information signal Always Below 1 Ω
G95-11 (SG-2) - Body ground L-Y - Body ground Ground for pulse position sensor (Mode damper servo) Always Below 1 Ω
G95-13 (SG-3) - Body ground BR-Y - Body ground Ground for cooler thermistor Always Below 1 Ω
G95-14 (SG-4) - Body ground P - Body ground Ground for No. 1 cooler thermistor Always Below 1 Ω
G95-16 (AGND) - G95-21 (AUXO) R-L - LG-R Input signal for pulse position sensor (recirculation damper servo)
·

Ignition switch ON

·

Blower switch on (LO level)

·

Air inlet control recirculation to fresh or vice versa


Pulse generation
G95-17 (PIA) - G95-21 (AUXO) P-B - LG-R Input signal for pulse position sensor (recirculation damper servo)
·

Ignition switch ON

·

Blower switch on (LO level)

·

Air inlet control recirculation to fresh or vice versa


Pulse generation
G95-18 (TR) - G95-13 (SG-3) GR - BR-Y Cooler thermistor signal
·

Ignition switch ON

·

Cabin temperature 25°C (77°F)


1.8 to 2.2 V
·

Ignition switch ON

·

Cabin temperature 40°C (104°F)


1.2 to 1.6 V
G95-20 (SG-1) - Body ground BR-Y - Body ground Ground for pulse position sensor (air mix damper servo) Always Below 1 V
G95-21 (AUXO) - Body ground LG-R - Body ground Ground for pulse position sensor (recirculation damper servo) Always Below 1 Ω
G95-23 (PMB) - G95-20 (SG-1) W-L - BR-Y Input signal for pulse position sensor (air mix damper servo)
·

Ignition switch ON

·

Blower switch on (LO level)

·

Temperature switch MAX HOT to MAX COLD


Pulse generation
G95-24 (PMA) - G95-20 (SG-1) W-R - BR-Y Input signal for pulse position sensor (air mix damper servo)
·

Ignition switch ON

·

Blower switch on (LO level)

·

Temperature switch MAX COLD to MAX HOT


Pulse generation
G95-25 (POB) - G95-11 (SG-2) LG - L-Y Input signal for pulse position sensor (mode damper servo)
·

Ignition switch ON

·

Blower switch on (LO level)

·

Mode control FACE to DEF or vice versa


Pulse generation
G95-26 (POA) - G95-11 (SG-2) L-O - L-Y Input signal for pulse position sensor (mode damper servo)
·

Ignition switch ON

·

Blower switch on (LO level)

·

Mode control FACE to DEF or vice versa


Pulse generation


e.
E171008
2.708,1.417 3.063,1.573 0.354,0.156 10 false GND

Using an oscilloscope, check waveform 1.

Blower motor control signal
Item Content
Terminal No. (Symbol) G94-2 (BLW) - Body ground
Tool Setting 1 V/DIV., 50 μsec./DIV.
Condition Ignition switch ON, Blower switch on (LO level)

HINT:

When the blower level is increased, the duty ratio changes accordingly.



f.
E169152
2.76,1.177 3.094,1.333 0.333,0.156 10 false GND

Using an oscilloscope, check waveform 2.

Vehicle speed signal
Item Content
Terminal No. (Symbol) G94-9 (SPD) - Body ground
Tool Setting 5 V/DIV., 20 ms./DIV.
Condition Driving at approximately 20 km/h (12 mph)

HINT:

As the vehicle speed increases, the wavelength becomes shorter.




CHECK ECM (for 1KD-FTV except DPF and i-ART)


E170985
1.552,0.177 1.948,0.406 0.396,0.229 2.792,0.177 3.188,0.406 0.396,0.229 4.177,0.177 4.573,0.406 0.396,0.229 5.344,0.177 5.74,0.406 0.396,0.229 1.615,0.208 1.938,0.417 0.323,0.208 10 false C22 2.865,0.208 3.208,0.406 0.344,0.198 10 false C23 4.25,0.208 4.625,0.438 0.375,0.229 10 false G38 5.406,0.208 5.771,0.417 0.365,0.208 10 false G39

a.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G38-18 (AC1) - C23-7 (E1) Y - BR Idle-up request signal
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch on


Below 1 V
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch off


11 to 14 V
G38-19 (ACT) - C23-7 (E1) R-L - BR Magnet clutch on permit output signal
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch off or on (magnet clutch off)


11 to 14 V
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch on (magnet clutch on)


Below 1 V



CHECK ECM (for 1KD-FTV for DPF)


A224896
0.563,0.448 0.948,0.677 0.385,0.229 6.219,0.448 6.604,0.677 0.385,0.229 5.167,0.448 5.552,0.677 0.385,0.229 4.135,0.448 4.521,0.677 0.385,0.229 3.021,0.448 3.406,0.677 0.385,0.229 1.615,0.448 2,0.677 0.385,0.229 0.594,0.49 0.958,0.667 0.365,0.177 10 false G149 6.25,0.49 6.688,0.667 0.438,0.177 10 false C112 5.198,0.49 5.656,0.667 0.458,0.177 10 false C111 4.167,0.49 4.563,0.667 0.396,0.177 10 false C114 3.063,0.49 3.458,0.667 0.396,0.177 10 false C113 1.635,0.49 1.99,0.667 0.354,0.177 10 false G148

a.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G148-10 (AC1) - C112-1 (E1) Y - BR Idle-up request signal
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch on


Below 1 V
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch off


11 to 14 V
G148-13 (ACT) - C112-1 (E1) R-L - BR Magnet clutch on permit output signal
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch off or on (magnet clutch off)


11 to 14 V
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch on (magnet clutch on)


Below 1 V



CHECK ECM (for 1KD-FTV for i-ART)


A224896
0.563,0.448 0.948,0.677 0.385,0.229 6.219,0.448 6.604,0.677 0.385,0.229 5.167,0.448 5.552,0.677 0.385,0.229 4.115,0.448 4.5,0.677 0.385,0.229 3.031,0.448 3.417,0.677 0.385,0.229 1.604,0.448 1.99,0.677 0.385,0.229 0.594,0.49 0.958,0.667 0.365,0.177 10 false G157 6.25,0.49 6.688,0.667 0.438,0.177 10 false C164 5.198,0.49 5.656,0.667 0.458,0.177 10 false C163 4.146,0.49 4.542,0.667 0.396,0.177 10 false C167 3.063,0.49 3.458,0.667 0.396,0.177 10 false C166 1.635,0.49 1.99,0.667 0.354,0.177 10 false G156

a.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G156-10 (AC1) - C164-6 (E1) Y - BR Idle-up request signal
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch on


Below 1 V
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch off


11 to 14 V
G156-13 (ACT) - C164-6 (E1) R-L - BR Magnet clutch on permit output signal
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch off or on (magnet clutch off)


11 to 14 V
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch on (magnet clutch on)


Below 1 V



CHECK ECM (for 2TR-FBE)


A224896
0.563,0.448 0.948,0.677 0.385,0.229 6.219,0.448 6.604,0.677 0.385,0.229 5.156,0.448 5.542,0.677 0.385,0.229 4.115,0.448 4.5,0.677 0.385,0.229 3.021,0.448 3.406,0.677 0.385,0.229 1.625,0.448 2.01,0.677 0.385,0.229 0.594,0.49 0.958,0.667 0.365,0.177 10 false G145 6.292,0.49 6.594,0.667 0.302,0.177 10 false C98 5.229,0.49 5.531,0.667 0.302,0.177 10 false C97 4.188,0.49 4.49,0.667 0.302,0.177 10 false C96 3.094,0.49 3.396,0.667 0.302,0.177 10 false C95 1.656,0.49 2.031,0.688 0.375,0.198 10 false G146

a.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G146-19 (AC1) - C98-5 (E1) Y - BR Idle-up request signal
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch on


Below 1 V
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch off


11 to 14 V
G146-21 (ACT) - C98-5 (E1) R-L - BR Magnet clutch on permit output signal
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch off or on (magnet clutch off)


11 to 14 V
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch on (magnet clutch on)


Below 1 V



CHECK ECM (for 1GR-FE)


E127538
5.75,0.177 6.146,0.375 0.396,0.198 4.625,0.177 5.021,0.375 0.396,0.198 3.375,0.177 3.771,0.375 0.396,0.198 2.156,0.177 2.552,0.375 0.396,0.198 0.979,0.177 1.375,0.375 0.396,0.198 5.792,0.198 6.292,0.375 0.5,0.177 10 false G155 4.656,0.198 5.156,0.375 0.5,0.177 10 false G154 3.417,0.198 4.021,0.375 0.604,0.177 10 false C131 2.198,0.208 2.646,0.385 0.448,0.177 10 false C130 1.021,0.198 1.542,0.375 0.521,0.177 10 false C129

a.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G154-24 (AC1) - C131-1 (E1) Y - BR Idle-up request signal
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch on


Below 1 V
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch off


11 to 14 V
G154-25 (ACT) - C131-1 (E1) R-L - BR Magnet clutch on permit output signal
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch off or on (magnet clutch off)


11 to 14 V
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch on (magnet clutch on)


Below 1 V



CHECK ACCESSORY METER ASSEMBLY


E225684
1.448,0.313 1.969,0.573 0.521,0.26 1.573,0.365 1.875,0.573 0.302,0.208 10 false G32

a.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G32-3 (TH+) - G32-2 (SG) W-G - BR-Y Thermistor assembly signal
·

Ignition switch ON

·

Ambient temperature 20 to 30°C (68 to 86°F)


1.0 to 1.6 V
·

Ignition switch ON

·

Ambient temperature 30 to 50°C (86 to 122°F)


0.6 to 1.0 V
G32-9 (DATA) - G32-1 (GND1) P - LG Ambient temperature signal Ignition switch ON Pulse generation



CHECK COMBINATION METER ASSEMBLY


E165587
3.354,0.333 3.75,0.563 0.396,0.229 3.427,0.365 3.792,0.573 0.365,0.208 10 false G19

a.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G19-6 (+S) - G19-22 (EP) V-R - Y Vehicle speed signal Driving at approximately 20 km/h (12 mph) Pulse generation
(See waveform 1)


b.
E169152
2.76,1.177 3.135,1.354 0.375,0.177 10 false GND

Using an oscilloscope, check waveform 1.

Vehicle speed signal
Item Content
Terminal No. (Symbol) G19-6 (+S) - G19-22 (EP)
Tool Setting 5 V/DIV., 20 ms./DIV.
Condition Driving at approximately 20 km/h (12 mph)

HINT:

As the vehicle speed is increased, the wavelength becomes shorter.