Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) › 2011.10–2012.10
RM1840EF _58 Vehicle Interior _009648 HEATING / AIR CONDITIONING _0052762 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  Heater Relay Circuit  


DESCRIPTION

The No. 1 heater relay is turned on by signals from the air conditioning amplifier assembly. The No. 1 heater relay supplies power to the blower motor control.

WIRING DIAGRAM

E225442
5.917,0.594 6.156,0.771 0.24,0.177 10 false HR 4.448,0.99 5.51,1.635 1.063,0.646 10 false to Blower Motor Control 4.469,1.875 5.458,2.604 0.99,0.729 10 false to Blower with Fan Motor Sub-assembly 3.396,1.448 3.844,2.052 0.448,0.604 10 false No.1 Heater Relay 1.479,0.75 2.719,0.948 1.24,0.198 10 false ECU-IG&GAUGE 3.125,1.438 3.26,1.594 0.135,0.156 10 false 4 2.927,0.5 3.063,0.656 0.135,0.156 10 false 1 2.927,0.906 3.063,1.063 0.135,0.156 10 false 5 3.656,0.51 3.792,0.667 0.135,0.156 10 false 2 3.677,0.906 3.813,1.063 0.135,0.156 10 false 3 1.875,1.635 2.427,1.833 0.552,0.198 10 false FR HTR 5.615,2.698 6.823,3.125 1.208,0.427 10 false Air Conditioning Amplifier Assembly 5.604,2.552 5.979,2.698 0.375,0.146 10 false G94 5.688,0.51 5.865,0.656 0.177,0.146 10 false 14 0.469,1.427 1.292,1.625 0.823,0.198 10 false from Battery 0.469,0.573 1.229,0.958 0.76,0.385 10 false from Ignition Switch

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT NO. 1 HEATER RELAY
a.
B106753
2.51,0.844 2.51,0.615 false 2.854,1.177 3.042,1.177 false 2.49,1.521 2.49,1.708 false 2.083,1.219 2.083,1.708 false 2.479,1.021 1.802,1.01 false 0.813,0.125 0.906,0.323 0.094,0.198 10 false 4 0.323,0.781 0.417,0.979 0.094,0.198 10 false 5 1.313,0.781 1.406,0.979 0.094,0.198 10 false 3 0.323,1.594 0.417,1.792 0.094,0.198 10 false 1 1.313,1.583 1.406,1.781 0.094,0.198 10 false 2 1.698,0.927 1.792,1.125 0.094,0.198 10 false 4 3.083,1.083 3.177,1.281 0.094,0.198 10 false 5 2.052,1.708 2.146,1.906 0.094,0.198 10 false 3 2.479,0.427 2.573,0.625 0.094,0.198 10 false 1 2.469,1.708 2.563,1.906 0.094,0.198 10 false 2

Remove the No. 1 heater relay from the driver side junction block assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>RELAY(for Heater)>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 4 Battery voltage is not applied to terminals 1 and 2 Below 1 Ω
3 - 5 10 kΩ or higher
3 - 4 Battery voltage is applied to terminals 1 and 2 10 kΩ or higher
3 - 5 Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (NO. 1 HEATER RELAY - AIR CONDITIONING AMPLIFIER, BATTERY AND BODY GROUND)

NG

2.CHECK HARNESS AND CONNECTOR (NO. 1 HEATER RELAY - AIR CONDITIONING AMPLIFIER, BATTERY AND BODY GROUND)
a.

Remove the No. 1 heater relay from the driver side junction block assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>RELAY(for Heater)>REMOVAL


b.

Disconnect the G94 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
No. 1 heater relay terminal 2 - G94-14 (HR) Always Below 1 Ω
No. 1 heater relay terminal 2 - Body ground Always 10 kΩ or higher
No. 1 heater relay terminal 3 - Body ground Always 10 kΩ or higher
No. 1 heater relay terminal 4 - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
No. 1 heater relay terminal 1 - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
No. 1 heater relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.
E225456
0.698,0.052 1.167,0.302 0.469,0.25 0.76,0.99 1.292,1.729 true 0.802,0.104 1.135,0.281 0.333,0.177 10 false G94 1.313,1.729 1.677,1.917 0.365,0.188 10 false MGC 0.073,0 0.292,0.198 0.219,0.198 10 false *a
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Remove the air conditioning amplifier assembly with its connectors still connected.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER(for Automatic Air Conditioning System)>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G94-14 (HR) - Body ground
·

Ignition switch off

·

Blower switch off


Below 1 V
·

Ignition switch ON

·

Blower switch on (LO level)


Below 1 V
·

Ignition switch ON

·

Blower switch off


11 to 14 V



Result:
Proceed to
OK
NG



OK

NG