Home › Vehicle Exterior › WINDOW / GLASS › WINDOW DEFOGGER WIRE
RM1840EF _59 Vehicle Exterior _009651 WINDOW / GLASS _0052788 WINDOW DEFOGGER WIRE G

WINDOW / GLASS  WINDOW DEFOGGER WIRE  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT BACK WINDOW GLASS (DEFOGGER WIRE)

NOTICE:
·

When cleaning the glass, wipe the glass along the wire using a soft, dry cloth. Take care not to damage the defogger wires.

·

Do not use detergents or glass cleaners that have abrasive ingredients.

·

When measuring voltage, wrap a piece of tin foil around the tip of the negative (-) tester probe and press the foil against the wire with your finger as shown in the illustration.



B066134
2.729,0.813 2.729,1.521 false 1.938,1.219 1.698,1.667 false 0.406,1.094 0.406,0.583 0.406,0.583 0.708,0.583 false 2.667,1.552 2.854,1.708 0.188,0.156 10 false *1 1.583,1.698 1.771,1.854 0.188,0.156 10 false *2 0.75,0.49 0.938,0.646 0.188,0.156 10 false *3
*1 Defogger Wire
*2 Tin Foil
*3 Tester Probe


a.

Turn the ignition switch to ON.


b.

Turn the defogger switch on.


c.
B119840
2.344,0.583 1.281,0.99 false 0.823,0.896 1.281,1.083 0.458,0.188 10 false Center

B119841
2.24,1.031 1.833,1.875 false 0.896,0.792 1.271,0.792 1.271,0.792 1.729,1.104 false 3.094,0.115 3.146,0.115 3.146,0.115 3.146,0.958 false 2.396,0.708 2.563,0.708 2.563,0.708 2.563,0.958 false 3.25,1.625 2.646,3.219 2.646,3.219 2.438,3.219 false 1.156,0.198 1.292,0.198 1.292,0.198 1.74,0.521 false 0.281,0.688 0.917,0.885 0.635,0.198 10 false Foil Strip 0.344,0.115 1.208,0.313 0.865,0.198 10 false Ground Side 1.313,1.896 2.125,2.135 0.813,0.24 10 false Broken Wire 2.146,0.615 2.406,0.813 0.26,0.198 10 false 0 V 1.854,0.042 3.125,0.24 1.271,0.198 10 false Approximately 10 V 1.646,3.135 2.458,3.333 0.813,0.198 10 false Battery Side

Measure the voltage at the center of each defogger wire as shown in the illustration.

Standard Voltage:
Voltage Diagnosis
approximately 5 V Wire is not broken
approximately 10 or 0 V Wire is broken


HINT:

If there is approximately 10 V, the wire may be faulty between the center of the wire and the wire end on the ground side. If there is no voltage, the wire may be faulty between the center of the wire and the wire end on the battery side.



d.

Place the voltmeter positive (+) lead against the defogger wire on the battery side.


e.

Place the voltmeter negative (-) lead with the foil strip against the wire on the ground side.


f.

Slide the positive (+) lead from the battery side to the ground side.


g.

The point where the voltage drops from approximately 10 V to 0 V is where the defogger wire is broken.

HINT:

If the defogger wire is not broken, the voltmeter indicates 10 V at the positive (+) end of the defogger wire and gradually decreases to approximately 0 V as the meter probe moves to the other end.