Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(w/o Jam Protection Function) › 2011.10–2012.04
RM1840EF _59 Vehicle Exterior _009651 WINDOW / GLASS _0052792 POWER WINDOW CONTROL SYSTEM(w/o Jam Protection Function) J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(w/o Jam Protection Function)  Driver Side Power Window Manual Function does not Operate with Power Window Master Switch  


DESCRIPTION

If the manual up/down function does not operate, a malfunction may be present in the power window regulator master switch assembly, front power window regulator motor assembly LH or wire harness.

WIRING DIAGRAM

B286740
4.99,0.792 5.188,1.021 0.198,0.229 10 false U 4.969,3.063 6.542,3.573 1.573,0.51 10 false Power Window Regulator Master Switch Assembly 0.281,0.667 2.198,1.167 1.917,0.5 10 false Front Power Window Regulator Motor Assembly LH 1.208,1.698 2.208,1.917 1,0.219 10 false from IG1 Relay 3.427,1.865 3.823,2.063 0.396,0.198 10 false PWR 4.99,1.688 5.167,1.885 0.177,0.198 10 false B 4.99,2.427 5.146,2.625 0.156,0.198 10 false E 4.99,1.146 5.167,1.344 0.177,0.198 10 false D 0.281,0.521 0.563,0.688 0.281,0.167 10 false I3 3.385,0.688 3.563,0.844 0.177,0.156 10 false 2 3.385,1.01 3.563,1.167 0.177,0.156 10 false 1 4.969,2.896 5.927,3.083 0.958,0.188 10 false I12*1, I13*2 4.365,0.688 4.906,0.885 0.542,0.198 10 false 4*1, 3*2 4.365,0.979 4.896,1.208 0.531,0.229 10 false 9*1, 4*2 4.365,1.594 4.927,1.823 0.563,0.229 10 false 6*1, 9*2 4.365,2.323 4.906,2.531 0.542,0.208 10 false 3*1, 1*2 3.188,0.792 3.385,1.021 0.198,0.229 10 false U 3.188,1.115 3.365,1.313 0.177,0.198 10 false D 0.188,3.313 1.76,3.552 1.573,0.24 10 false *2: except Double Cab 0.188,3.01 1.448,3.25 1.26,0.24 10 false *1: for Double Cab

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
a.
B276330
0.135,0.875 0.667,1.167 0.531,0.292 2.208,0.26 1.938,1.021 false 2.427,0.26 2.208,0.26 false 1.24,0.25 1.354,1.031 false 1.24,0.25 1.052,0.25 false 0.323,0.948 0.594,1.115 0.271,0.167 10 false I12 2.469,0.177 2.656,0.354 0.188,0.177 10 false B 0.083,0 0.281,0.188 0.198,0.188 10 false *a 0.927,0.167 1.073,0.354 0.146,0.188 10 false E
*a Front view of wire harness connector
(to Power Window Regulator Master Switch Assembly)


for Double Cab:

i.

Disconnect the I12 power window regulator master switch assembly connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I12-6 (B) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I12-3 (E) - Body ground Always Below 1 Ω




b.
B290653
0.094,0.74 0.625,1.031 0.531,0.292 2.427,1 2.615,0.396 2.615,0.396 2.75,0.396 false 1.51,1.438 1.729,1.938 1.729,1.938 1.927,1.938 false 0.292,0.802 0.552,0.969 0.26,0.167 10 false I13 1.948,1.844 2.104,2.021 0.156,0.177 10 false B 0.083,0.104 0.354,0.323 0.271,0.219 10 false *a 2.813,0.313 2.99,0.479 0.177,0.167 10 false E
*a Front view of wire harness connector
(to Power Window Regulator Master Switch Assembly)


except Double Cab:

i.

Disconnect the I13 power window regulator master switch assembly connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I13-9 (B) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I13-1 (E) - Body ground Always Below 1 Ω




Result:
Proceed to
OK
NG



OK

2.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
a.
B276330
0.156,0.854 0.688,1.146 0.531,0.292 2.854,0.854 2.479,1.031 false 1.083,0.198 1.271,0.198 false 1.521,1.042 1.271,0.198 false 2.917,0.76 3.052,0.938 0.135,0.177 10 false D 0.958,0.115 1.125,0.281 0.167,0.167 10 false U 0.115,0.01 0.354,0.188 0.24,0.177 10 false *a 0.344,0.917 0.656,1.094 0.313,0.177 10 false I12
*a Front view of wire harness connector
(to Power Window Regulator Master Switch Assembly)


for Double Cab:

i.

Disconnect the I12 power window regulator master switch assembly connector.


ii.

Check operation of the front power window regulator motor assembly LH.

OK:
Measurement Condition Specified Condition
Battery positive (+) → I12-4 (U)Battery negative (-) → I12-9 (D) Power window moves up
Battery positive (+) → I12-9 (D)Battery negative (-) → I12-4 (U) Power window moves down




b.
B290653
0.094,0.75 0.625,1.042 0.531,0.292 1.427,0.99 1.271,0.469 1.271,0.469 1.083,0.469 false 1.188,1.146 0.906,1.833 0.906,1.833 0.719,1.833 false 0.281,0.813 0.542,0.979 0.26,0.167 10 false I13 0.063,0.01 0.25,0.188 0.188,0.177 10 false *a 0.948,0.375 1.271,0.542 0.323,0.167 10 false U 0.594,1.75 0.896,1.917 0.302,0.167 10 false D
*a Front view of wire harness connector
(to Power Window Regulator Master Switch Assembly)


except Double Cab:

i.

Disconnect the I13 power window regulator master switch assembly connector.


ii.

Check operation of the front power window regulator motor assembly LH.

OK:
Measurement Condition Specified Condition
Battery positive (+) → I13-3 (U)Battery negative (-) → I13-4 (D) Power window moves up
Battery positive (+) → I13-4 (D)Battery negative (-) → I13-3 (U) Power window moves down




Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
a.

Disconnect the I12*1 or I13*2 power window regulator master switch assembly connector.


*1: for Double Cab

*2: except Double Cab


b.

Disconnect the I3 front power window regulator motor assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Double Cab
Tester Connection Condition Specified Condition
I12-9 (D) - I3-1 (D) Always Below 1 Ω
I12-4 (U) - I3-2 (U) Always Below 1 Ω
I12-9 (D) or I3-1 (D) - Body ground Always 10 kΩ or higher
I12-4 (U) or I3-2 (U) - Body ground Always 10 kΩ or higher


except Double Cab
Tester Connection Condition Specified Condition
I13-4 (D) - I3-1 (D) Always Below 1 Ω
I13-3 (U) - I3-2 (U) Always Below 1 Ω
I13-9 (D) or I3-1 (D) - Body ground Always 10 kΩ or higher
I13-3 (U) or I3-2 (U) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR