Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › from 2012.10
RM1840EF _59 Vehicle Exterior _009652 DOOR / HATCH _0052799 FRONT DOOR N

DOOR / HATCH  FRONT DOOR  ADJUSTMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·
B276679
0.625,1.75 0.896,1.979 0.271,0.229 10 false *1 2.531,1.75 2.771,1.958 0.24,0.208 10 false *2
*1 Centering Bolt
*2 Standard Bolt


Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts on. Substitute the centering bolts for standard bolts when making adjustments.

·

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 1.INSPECT FRONT DOOR PANEL SUB-ASSEMBLY LH

a.

Check that the clearance measurements of areas A to M are within the standard ranges.

B276675
1.948,0.656 2.24,0.865 0.292,0.208 10 false A 2.281,1.156 2.49,1.344 0.208,0.188 10 false B 4.302,0.313 4.552,0.521 0.25,0.208 10 false C 4.469,0.896 4.667,1.073 0.198,0.177 10 false D 5.885,0.927 6.104,1.094 0.219,0.167 10 false E 6.104,1.427 6.292,1.604 0.188,0.177 10 false F 5.646,2.74 5.906,2.948 0.26,0.208 10 false G 6.063,2.896 6.25,3.083 0.188,0.188 10 false H 4.656,4.031 4.833,4.198 0.177,0.167 10 false I 4.573,3.542 4.76,3.729 0.188,0.188 10 false J 2.552,3.594 2.802,3.771 0.25,0.177 10 false K 2.958,3.76 3.135,3.927 0.177,0.167 10 false L 1.146,2.719 1.396,2.917 0.25,0.198 10 false M

Standard:
Area Specified Condition Area Specified Condition
A 3.6 to 6.6 mm (0.142 to 0.260 in.) B 1.5 to 4.5 mm (0.0591 to 0.177 in.)
C 3.6 to 6.6 mm (0.142 to 0.260 in.) D *1: 1.2 to 4.2 mm (0.0472 to 0.165 in.)
*2: 1.1 to 4.1 mm (0.0433 to 0.161 in.)
E *1: 3.0 to 6.0 mm (0.118 to 0.236 in.)
*2: 3.5 to 6.5 mm (0.138 to 0.256 in.)
F -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
G *1: 3.0 to 6.0 mm (0.118 to 0.236 in.)
*2: 3.5 to 6.5 mm (0.138 to 0.256 in.)
H -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
I 3.7 to 6.7 mm (0.146 to 0.264 in.) J 7.5 to 10.5 mm (0.295 to 0.413 in.)
K 3.2 to 6.2 mm (0.126 to 0.244 in.) L 1.0 to 4.0 mm (0.0394 to 0.158 in.)
M 3.1 to 6.1 mm (0.122 to 0.240 in.) - -


*1: for Single Cab, for Extra Cab

*2: for Double Cab


Hide 2.ADJUST FRONT DOOR PANEL SUB-ASSEMBLY LH

a.
B276676

Using SST, loosen the hinge bolts on the body and adjust the door position.

SST
09812-00010  


b.

Tighten the hinge bolts on the body after the adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


c.
B276677

Loosen the hinge bolts on the door and adjust the door position.


d.

Tighten the hinge bolts on the door after the adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


e.
B276678

Using a T30 "TORX" socket, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.


f.

Using a T30 "TORX" socket, tighten the striker mounting screws after the adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)